Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hello,
I'm using nRF52840 dongle. I implemented a virtual COM port to send messages to my computer. My problem is that I can send messages only if I'm already connected...
Hello everyone, I ask for help to install the new version of SES in Ubuntu Linux 18, since the license is not recognized by the em nor the hardware, I can program the card...
After enter low power mode I aim to config to wake up on a 1 sec timer, but in 20 us the event 0x26 comes. I cannot find what event ID 0x26 is and how to disable it ?
Info...
I am having an issue when building the hci rpmsg example for the following youtube tutorial
Zephyr RTOS and Bluetooth LE on the dual-core nRF5340
I've tried figuring this...
Hello,
According to the description in below page, " The image can be an application image, SoftDevice image, bootloader image, or a combined image of bootloader and SoftDevice...
I am trying to interface adxl362 sensor with ANNA-B112 evaluation board.i am trying to read the part id to check the connection. The code is pasted below.
nrf_drv_spi_config_t...
Hi! I am using the 52840-DK dev board.
I want to use two pins, P1.0 and P1.1 as GPIO output pins.
In my code I have;
nrf_gpio_cfg_output(BLE_CONNECTED); nrf_gpio_pin_clear...
Hi everyone,
I want to serial print three float values (x,y,z) from an IMU. I use the MACRO NRF_LOG_ERROR( "Float_Value: " NRF_LOG_FLOAT_MARKER "\r\n", NRF_LOG_FLOAT(value...
Race condition in starting the ADC following calibration. I am trying to start the ADC in the interrupt routine when the end calibration is reported, however I have unreliable...
Hello,
I have two brand new nRF52 DK eval boards version 2.0. On both boards, the reverse charging diode D8 is missing. That diode is required to power the board externally...
Just trying to build Nordic sample codes S110 with nRF51822.
Here is the error. These are hidden file. I guess some configuration is not correct but I'm not sure.
---...
SDK: 15.1 IDE: Keil Softdevice: S132 v6.0 Hello, I am using the ble_app_uart example as a starting point. My goal is to send 5 bytes every 5 seconds to another nRF52 Development...
Hi:
I'm supporting a nrf52832 project that is using SDK 11 with S132 Softdevice 2.0.0, and would like to get to the bottom of a lingering workaround that's been in place...
