It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I want nRF52 Continuous Unmodulated TX carrier.
Is it possible by TASK_TXEN and TASK_START or radio_tx_carrier command of radio test example, after TX configuration...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi, team I am trying to build a system with one master and multiple slaves using the mesh SDK. ( This is similar to the light_switch example. ) At this, I want to give each...
After the update to nRF Connect v3.0.0 none of the Nordic devices is detected anymore by that tool.
I even un-installed and reinstalled nRF Connect v3.0.0 (as recommended...
Went through the pin_change_int example and of course it works fine.
Migrated that to custom board and it also worked fine with main loop.
So I then tried to use that...
Have an application that configures a wifi SOC using spim before enabling BLE scanner.
When it is running there are 4 timer events running and the main loop check status...
Hello,
Zephyr 1.14.0 includes the nrfx code to use GPIOTE and PPI and my code compiles but I get
undefined reference errors to the nrfx_gpiote_ and nrfx_ppi_ functions...
Few issues I'm facing -
1. I have gone through the related blogs, tutorial, documentation for DFU. nRFConnect cannot connect to the Fanstel BM832 chip. It gives me an error...
hi
I connect AT24C02 EEPROM with nrf52dk.
I already test EEPROM with arduino and it work fine.
Now i want to communicate with NRF52DK kit,so which example I would prefer...
Hi Nordic.
I have an issue that I'm really stuck on. I am trying to send data from a radar sensor via your nRF52 DK BLE board. I've managed to make a working connection...
Hello,
we would like to use a nRF52DK for a simple bluetooth production testing as mentioned in AN34. If we are using an external 50R antenna on J1 do we need to cut the...
I am using nRF52832 SDK 15.2.
I would like to avoid using the 32.768kHz oscillator to save space and cost.
I am using BLE and sleep mode ON.
I defined in sdk_config...
If I build/flash from the command line with "west build -b nrf9160_pca10090ns" and "west flash -d build" it loads a fully combined image with mcuboot and (spm+application...
