Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
I have a rare issue where my device won't advertising as it is waiting for a Pending Flash event to clear. However I want to add a supervisor time-out to this. It is safe...
Hi ,
I am getting error in pstorage_store function .
On further digging function
if ((!is_word_aligned(p_src))) is returning the error.
What does this function check...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE. If the program is wrong,The chip will reset, I want to save some data to the FLASH area before the chip reset. What I need to do...
The example DFU project (dual_bank_ble_s110) for NRF51422 seems to work just fine on my custom board that has NRF51822. Is there a problem to use it like that if I set the...
Dear community,
I'd like to report a problem on the Direct Test Mode software provided in nrf51 SDK v6.1.0.
In this mode, 2-bytes commands are transmitted over the serial...
Whenever I try to run the following Convolution function for the 12th time in my code, the Processor is halted and I get the following Error on console:
Performing single...
According to this example, the device should be advertising RX and TX Characteristics. I also believe that when I connect to the UART app using my iphone, I should be able...
I have been successfully using my nRF52 Dev Kit (PCA10040) for the last few days. Today, when messing around with the UART drivers, I seem to have messed up the JLink-OB....
Hello,
I have an NRF51822 beacon board and two small 0.96" OLED displays (does not matter for me which one o use). One with GND, VDD, D0, D1, REST, D/C, CS and VCC pins...
I'm on windows 8 using the 1.0.1 sniffer application and wire shark 1.10.14 64bit with a Nordic nrf51 dongle. I'm using an nrf51 dev board with ble_peripherals/ble_app_blinky...
with nrf51 there is 2 blocks (block0 for softdevcie and block1 for user data and stack). I configured the system to retain RAM before going down using sd_power_ramon_set(0x00030003...
Hi,
I have a device that is configured to work in GAP central role. This device only scans for specific advertisements from specific devices. Could you suggest how I can...
Hi!
I used the develop board test the application "ble_app_multilink_central" and "ble_app_multilink_peripheral",but it is always connected failed,and disconnect Reason 0x0008...
Hi there. I have a very long C code that is running correctly on Code:Blocks, Ubuntu Terminal ( using GCC ), Eclipse and on Dev-C++.
However, when I put in on the board...
Hello,
I've been trying to control MCP23017 IO expander with TWI using nRF52832. When I execute the code it stops at nrf_drv_twi_tx. The address pins A(0:2) are 0.
Any...
