Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi,
just for understanding what soft device do i have to use when i want to build an application wich use observer role and broadcaster role at same time?
Can i use S110...
In our application, we need to save a group of data objects,
how many data objects in a group is dynamic.
also each data object has different sizes,
a few bytes up to 100...
Hi,
I am using nrf51822 custom board.
I'm trying to make intterrupt when a pin is 0 (or 1) and do some calculations while it remains 0.
However I could not manage...
Hello,
I am trying to use SPI on a mbed nRF51822 and am following the documentation suggestion. We've deleted all code except the minimum to try and track down the problem...
Hi,
i want to build an applicaiton with gcc and eclipse setup and S130. I use OSX.
if i don't use the softdevice and run it with the blank linkerscript my blinky code...
Hello,
We are trying to update to Keil uvision 5.11 and unfortunately breaking our teeth on the pack Installer. The Nordic SDK 5.2.0 is installed on the machine but when...
Hi,
I have installed nRF Master Control Panel app on custom board running Android kitkat 4.4.2(ASOP).
But when I run MCP app it gives prompt that 'Device doesn't support...
Hi all,
I develop a central application, which manages multiple peripheral connections. The application often has to stop and start scanning again. In rare cases the function...
Hi,
I'm trying to get the bootloader from SDK v6 running with SoftDevice v7.
I managed to compile it under Eclipse (gcc). I've just removed buttons and LEDs from the code...
I would like someone from Nordic to confirm that the new softdevice release s110_nrf51822_7.0.0 is not suitable for the 128kb versions of the chip (in my case nRF51822 QFABB0...
Hi!
How is the functionality choosen, the nRF51822 has to offer?
Is the SoftDevice (e.g. SD120) an API in C where a specific functionality (e.g. central role listening to...
Is it possible to use nRF51822 Development Kit without nRFgo Starter Kit? What I need - is to be able to connect couple of LEDs and buttons, can this be achieved without buying...
Hello,
after successfully calling sd_softdevice_enable(), I call ble_cscs_init() and that function returns with error code 7, which means NRF_ERROR_INVALID_PARAM. I've tracked...
