I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
I (think I) have successfully located the code responsible for handling the data received BUT! The code segment:
in app_uart_fifo.c
seem to only receive a paltry 1...
Hello
I want to measure Low power current in nrf52840-DK with System ON mode.
I need to know how much current consumes by nrf52840 SoC while I2C Engine ON, SPI ON, and...
Hi.
I am working with the nrfConnect SDK 1.8.0. I would like to configure the nrf5340 for maximum throughput to work as a server for a smartphone device.
How should...
Hi all,
I am using NRF52840 and I am saving some data to the flash memory using fds. The data are 216 bytes in each file and there are 3400 files which is in total 734kbytes...
Hi,
In my application, I am writing in flash.
But when I do so, my openthread data in flash gets o verwritten, the node doesn't retain its commissioning data.
In nrf_SDK_For_Thread_and_Zigbee...
Hi All ,
I am using nrf9160Dk ,When i use asset tracker V2 i successfully get the GPS values on the nrf Cloud . But when i use the Asset Tracker only then i am unable to...
Hi there,
From the product specification of the nrf5340, we can only find UARTE peripherals (UART with EasyDMA). Is it possible to implement uart without DMA? Of course...
Hi
I was just curious as to whether or not there is a specific reason the Xenon's PWM capabilities are not available with NCS/Zephyr. Is there a hard limitation or is this...
Hi Team,
SDK - 17.1.0
chip -nrf52810
I want to store sensor data (12 bytes) every 30 seconds in flash memory. Once the flash is full, I want to replace the old data...
I'm trying to interface with the ds1339 real time clock to set and read the time for timestamping tasks in ncs 1.8.0. I've found a few tutorials that boil down to:
1....
Hello !
I can see this error event is deprecated.
What other registers can be used if any error occurs during on-fly encryption/decryption process ?
In case of RX ,...
Hi,
I was implementing ZigBee coordinator in nrf connect v1.18.0 to connect sensor which develops from template sample. every thing went fine until I add install code (took...
Hi there!
I face issue with setting the connection using PHY Coded.
I've:
- set the #define NRF_BLE_SCAN_SCAN_PHY 4 (it's Coded one) on Central side.
- forced PHY...
