Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
In PCB phase of the product, I used mt8852b to conduct the ble measurement test,When assembling the finished product, I want to verify that the Bluetooth connection is good...
Hi Nordic team,
Summary: Shall we get nRF5340 based BLE mesh demo to test data relay from one node to another node.
Details:
We requires BLE mesh demo sample for testing...
Hello guys.
We use NCS v1.4.2 and Zephyr RTOS to develop the application code for our nRF52840 SoC.
Thanks to your support, we were able to use Zephyr ADC APIs and take...
I want to control the connection to send data for about 100ms, but the service discovery process takes about 300ms. When the service characteristics are known, I want to inform...
Hi, our application uses a nrf52840 module and a nrf52840 dongle. ( sdk15.0.0) in the application.
The central sends data to the peripheral continuously on an event. When...
I am trying to do some power measurements on the nRF5340 using the power profiler.
As suggested in the guide here, I am removing serial support to reduce power consumption...
Provide your AWS credentials page for Asset Tracker Cloud Example for AWS mentions sub-accounts. There is absolutely no such thing as a sub-account in AWS. The page is totally...
Hi.
I've been working with the nRF52840 for a couple of months. I started working on SEGGER IDE, but I've found that it was quite difficult to understand the behavior of...
I played around with the SAADC sampling A4 pin. When I connect to GND, I see negative values sometimes. If I connect to 3.3V I see value 235/236 which is, what I expect. ...
I have 2 device gateway and nrf52840 board.
Can i get zigbee distance?? I think RSSI data is possible. Right??
If you can measure the distance between gateway and nrf52840...
Hello,
I am using nRF52833, nRF Connect SDK v1.4.2.
I have imported the Zigbee light switch, light bulb, network_coordinator build and test it successfully.
I have also...
I should not be asking this question here but it should be documented! SoftDevice s130.
A possible error I can get when executing sd_mutex_acquire() is NRF_ERROR_SOC_MUTEX_ALREADY_TAKEN...
Hi All,
Hardware: Custom Board (Buttonless)
SDK : 17.0.2
SD: 7.2.0
Support required: DFU Buttonless
We are able to successfully load and run the DFU buttonless...
I am using nRF52832.
Can I use NFC1/P0.09 as SCL and NFC2/P0.10 as SDA?
nRF52832_PS_v1.4.pdf states "The pin capacitance will be higher on these pins" in 4.3.2.
I am...
I posted one question in my earlier ticket about download firmware to our own device (nRF9160) through DK of NRF9160.
Now we are design the schematic of our own device with...
