Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi,
I would like to flash a CC3100MOD wifi chip from TI with the Nordic 52832 chip as a host. Attached is my schematic. I am fairly new to the nordic family but I have...
Hi,
The problem statement mentioned below.
What we are trying to do is Read Light value from the MAX44009 sensor on the TWI interface.
Looking at the data sheet for...
Hi,
I am using Nordic nRF52840 SoC with nRF5_SDK_15.2.0_9412b96 (SDK) and S140 softdevice. I tried to set Tx power to +8dbm using
rc = sd_ble_gap_tx_power_set (BLE_GAP_TX_POWER_ROLE_ADV...
I am currently involved in developing a product that is using the nrf52840. The product needs to keep precise time across a wide range of temperatures, which is why a 32Mhz...
Hi,
When I try spi commnucation with sensor on nrf52840 (using Mbed OS with SDK14.2), it stuck to nrf_spim_task_trigger (p_spim, NRF_SPIM_TASK_START); while spim_xfer is...
Hi,
I am trying to increase the sampling rate of the motion sensor on a Thingy:52. I managed to update the firmware and increase the BLE_GAP_ADV_INTERVAL_MAX from 200 to...
I am using softdevice s132, nRF52832 and SDK 15.3
This happens every time I connect the RX line.
This is an application where I implement UART with the HRS application...
Hi,
I am interested to know how to make a mesh node (for example, a light server) compatible to perform a DFU.
I have gone through the DFU page and I noticed that the...
Hello.
I am about to receive the Uart service for the Nordic SDK Central and peripheral.
I Use nrf 52832.
In the peripheral example, we used 'ble_nus_data_send'...
Hi,
I am using nRF52840 Enineering C chip on a custom board using SDK v15.3.0 with SoftDevice v6.1.1
I have modified the Blinky Central code and the Blinky Peripheral...
Hi. After my nRF52832 peripheral connects to an android / iOS, I am trying to read the MTU size that has been negotiated with the following code;
current_mtu is being...
The NVMC writting functions hasn't return values,
void nrf_nvmc_write_bytes(uint32_t address, const uint8_t * src, uint32_t num_bytes)
Does it mean that all internal...
When nRF52840 P0.09 / P0.10 are used as GPIOs, the datasheet indicates they can be used for "low frequency I/O only". What is the frequency limit on these pins? Would it be...
