Hi,
I am working with nrf5340 chip and I want to migrate from NCS 2.6.1 to NCS 2.7.0. I want therefore to apply recommendations: migrate to sysbuild.
With NCS 2.6.1 I...
I am using MX25 external flash with nRF9160. I am unable to find the configuration to use the Zephyr APIs to access the flash. I am able to access it when I am using
spi_write_dt...
Attribute reporting is automatically handled by the ZBOSS stack which generates the Report Attribute commands. Is it possible to set the Disable Default Response bit in the...
Hi all,
I've followed the instruction to setup nRF sniffer with Wireshark.
But unfortunately, I see this error when I'm trying to start a new capture with my nRF Sniffer...
Hi
I tried to run the sample "hci_pwr_ctrl" from the NCS v2.7.0 on the nRF54L15.
After starting the sample, the modification of the TX power level during the advertising...
Hi,
I realise this is now quite an old version of the SDK and this particular library is no longer supported, but we have not yet migrated our project (I did try once...
I'm using the nordic ppk II to measure the power consumption of my device.
In order to validate the charge (current integral) displayed by the PPK2 i put two PPK2 daisy...
Hi,
I am not sure how to read from a characteristic which doesnt have notify property in them. I started looking into nrf_ble_gq_item_add() But I am not sure on what parameters...
hi
I am trying to get the nrf7002 dk working, however, when i try to provision the kit using the nrf wifi provisioner app i get an error saying " scanning error received...
Hello,
I'm working on nrf5340 audio bis gateway sample.
The NCS version I use is v2.2.0, I know it's a very old version, but for some reason I can't update to the latest...
| Host | <---- UART ----> | nRF52833 (central) | <-- BLE--> | nRF52833 (Target) |
I have a requirement where I hope to update the central's firmware image through the Host...
Hello,
With the latest version of the nRF5340 MDK I am getting the following linker errors (below), and don't understand why they should turning up.
Best regards
==...
Hello,
The documentation in the nRF7002 Product Specification rev 1.0 says that the P2P mode (Peer-to-peer) is supported (section 6). However in this ticket: https://devzone...
I need to use ADC in the project, and then I have configured ADC in overlay. The code is as follows
The same code can be measured normally in Zephyr's ADC example, but...
Hi,
I'm trying to use an nRF52840 dev kit as an I2S-to-USB microphone, but I've been running into a problem where the recorded audio is periodically unusable.
To debug...
Hey Everyone ... Looking for some ideas / help with crash involving nRF Sniffer v2 and Wireshark. Specifically I have an older White MacBook that I use for sniffing and nRF...
Hi,
I am using sdk 16.0 and I am already using 3 SPI Instances i.e. SPI1, SPI2, SPI3. I wanted to use SPI0 Instance also. How to use it?
If enable SPI0 in sdk_config I...
Hello
I was working on nrf9160-dk with assert_trakker_v2 application successfully connecting to nrf Cloud. There was no problem.
Today I started the day by deleting it...
From what I understand, the nPM1100 can work without the battery (i.e. no BAT connection).
Does the Nordic Thingy:53 come with the Li-Po battery separated or is it mounted...
Good afternoon everyone, how are you?
I'm using custom hardware, Nrf52833+Nrf21540, already reviewed by and tuned by Nordic. We are going to carry out the tests for product...
I need to work on single bank DFU from esp32 to nrf52833. I found a website with instructions on single bank configuration here: academy.nordicsemi.com/.../topic /exercise...
Hello,
i'm working on a project where the system will be always in deep sleep unless there is an external event to wake him up. Upon this event, the system connects through...