During my development, I found NRF5 SDK only supports symmetric RX/TX data length settings.
Here is the on_data_length_update_request_evt in nrf_ble_gatt.c file.
static...
Hello,
I am working on a project that will require external flash. Is there an example program compatible with the following external flash device?
M95P08-I - Ultra low...
Hey,
the USB connection to my nRF54L15-DK isn't working anymore.
It is not showing up in nRF Connect Desktop and I can't find it under /dev/tty... or /dev/cu...
The...
I am relatively new to embedded and am wondering if there was a "best practices" guide / checklist for production deployment somewhere. Things like making sure you are using...
Hi. I'm trying to write a simple MQTT app. I am consistently getting these KConfig errors to do with variables I'm not using, and I have tried to set CMake to ignore these...
Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hello,
currently I am using the S110 Softdevice with the ble_template example as peripheral. This works fine.
For our final application, we need the central feature...
Question similar to this one
devzone.nordicsemi.com/.../
I have noticed that in the header ble.h included in the s310 folder, the function sd_ble_enable(..) and the type...
Hi Nordic expert, I wanna get a profile of 51822 performance cycle count. I found 51822 has no powerful DWT feature as cm3 or cm4, would you share me some feasible methods...
Hi All
I am aware that there are some changes to UV5.12 to do with Device Pack location etc.
I have currently updated my project from the .uvproj to .uvprojx extention...
I was able to setup gazell communication between two devices one as device and other as host using 32 byte payload size in nRf51822 module.
Here in gazell communication is...
We are using the Nordic Semi nRF51822-QFAC on our device for BLE. Since we are developing from scratch I understand we need have FCC testing done. Is there a summary of the...
I'm devloping application on nRf51 for that i'm using... SDK : nRF51_SDK_7.2.0_cf547b5 Tool chain : GNU tools arm Embedded [arm-none-eabi version 4.9.3] Dev Board : PCA10028...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I had a nRF81522 design that was working at 3.3V and I dropped the voltage to 1.9V. I didn't change anything else, but now I am getting periodic disconnects during interogation...
I have a PCA 10028.
This board uses Two microcomputers.
One is N51422.
Another is microcomputer on which the seal is put(Segger ID:).
What is the role of this microcomputer...
I recently discovered this article ( mbientlab.com/.../) and am trying to understand the data transfer type between the firmware ( ble_app_hrs_s110_pca10028 ) and an iOS device...
Hi,
Currently when I run the HRM demo I end up in the app error handler, unfortunately the error codes don't print to my terminal window. I'm using crossworks, and I was...
Hi,
I am new to using keil uvision. I am creating wearable solution, have enabled battery service indication, RTX support,bsp support, gpio,ble service.
When compiling...
Hello!
I would like to measure RSSI for different channels so as to decide which channel is the least noisy one (and more particularly, which ones are already used). I...
