There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
We have been trying to get the audio application to work using an external I2S microphone, but have recently run into the following problem when trying to send audio...
Hello Nordic,
I've been attempting to convert our system's TWIM implementation from the blocking to the non-blocking mode. I have been able to communicate fine with the...
Hi,
I have updated finally Segger Studio from version 7.22 to 8.14. Now I cannot compile the project. It ends with below error:
Build failed, exit status 0x1
Is something...
Hi, I have a problem where the mcuboot do not seem to include the 'jedec,spi-nor' driver. Looking at the build directory, /build/zephyr/zephyr.dts file has the device spi...
Hello everyone
our current project is to use dht22 to control an external fan
but we don't know how to add a new node to the device tree for the fan.
The picture below...
I got the license key for segger studio but the option to install the license is not popping up. https://drive.google.com/file/d/1qok8PcCYhHi_9nsknL2JW4_AtF6F5ZP5/view?usp...
Hello I have a few questions
In my project, the nPM1300 fuel gauge example via nrf5340dk works properly. I received information such as V - I - SOC via I2C. Currently I...
I try to use Gazell and USB HID to remote wake up my computer. But after compter turns into sleep, the callback function on the Gazell Host Device doesn't being called back...
The hardware I use is nrf52840Dongle, using nrf_dm sample for development. There are a few problems:
1. I have 8 devices, all within communication range, 4 as base stations...
Hi, I get a issue, build error if enabled PGPS in prj.conf:
CONFIG_NRF_CLOUD_PGPS =y
and OK if comment this config
for this project, I used sample/cellular/Location...
Hi,
For some reason, all of the VSCode action disappears after building the application with mcuboot using sysbuild on ncs 2.7.0. The application can only be built using...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
OK, I'm working with the nRF52832 and NCS V2.6.0, and I have two different actions I need to complete at various times with the SAADC:
Every ~ 3 seconds, I need to sample...
Hi,
I'm running some transceiver tests to look at extended broadcast and ISO transfer modes. I am using nrf5340_audio_dk and ncs V2.6.0 to run nrf5340_audio application...
When i try to run or debug the ble app uart example on our own hardware using the nrf52810 there is a fatal error when executing the code.
The example does run on the...
