There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hello,
I am not able to connect the nrf9160 with NB-IoT to the nRF Cloud using the asset_tracker_v2 or the multicell_location sample. I added the following configuration...
Hi
I have noticed that when I configure any GPIO with "NRF_GPIO_PIN_PULLUP" option, the CPU current is raised by approximatly 200 uA. (It doesn't matter if the GPIO is...
Hello, I have managed to get two NRF5340s linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to test again. And then I also need...
Hi,
I need to enable the ADC read and GPIO pin toggling to happen simultaneously at high precision, without using the MCU resources, approximately 15 us interval. After...
We have a device that is using the nrf_drv_csense module to measure a capacitive touch via the event_handler passed to nrf_drv_csense_init(). Unfortunately, due to various...
The latest versions of MbedTLS seem to have some level of support for TLS 1.3 that the nRF Connect library's MbedTLS version lacks. How can I use a newer version of MbedTLS...
Hello,
I am trying to use Eigen matrix library in a project on the nrf52832.
I was able to compile a very simple example however I get a mem_manage_fault while debugging...
I am trying to connect a low power camera Himax HM0360 to nRF52840 dk. In the camera device specification, it is mentioned that it provides I2C serial interface and full speed...
Hi, I'm just experimenting with my nRF9160 DK and have run into some questions regarding the default asset_tracker_v2 program and how some of it works. I have read the documentation...
Hi!
Basically, what it says in the title.
Datasheet mentions that for 2Mbps mode (enhanced shock burst) spacing should be 2Mhz or more.
Does that mean that number of...
Hello everyone,
I used nRF24L01 and Arduino to jamming 3 channel advertising BLE ( https://github.com/lws803/BLE-jammer ) and my Gateway can't receive message from my door...
I am trying to develop an environment based on the prx ESB sample and add nrfx_timer.h dependencies. This is not necessarily a question specific to this setup but a more general...
Hi,
I am using SDK 17 version. The file name is ble_app_uart_pca10040 . I send to data from nRF Connect app to nRF52 DK and this data reach correctly to nRF52. But i didn...
