Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
I am testing out the nRF Cloud MQTT multi-service example on my nRF9160 DK board. When looking at the GPS data on the cloud it is not very accurate and does not track my location...
Hi!
I am experiencing some odd behavior from the modem, and I hope you can help me understand it:
After I disconnect from LTE using lte_lc_func_mode_set(LTE_LC_FUNC_MODE_DEACTIVATE_LTE...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with a connection to an external MCU (#define MQTT_MESSAGE_BUFFER_LEN 8192) We tested...
I have not been able to create a stable development environment in macOS Monterey using the automatic installation process.
In order to better understand and document the...
Hi.
I'm working on a project based on the USB CDC ACM sample from Zephyr, which builds correctly for nRF5340DK, but gives an error when trying to build for nRF9160DK due...
Hello,
I am working on a project based on the nRF52810 custom board, I need to use several slave nodes to communicate to the gateway node/ server.
I need to improve...
Hi,
I want to use the nRF9160 SiP to connect via NB IoT to AWS IoT server but I don't want to use any SDK, I only want to use AT COMMANDS, there is some process that I could...
Earlier I created a project in SES for nRF5340. The simulation and debugging was quiet simple and easy to find the fatal errors, run time errors etc. Same features are not...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values from 0 to 10 using ADC with ble_app_uart. I have combined SAADC code and BLE_APP_UART code...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi !
I use the NRF52832 and with Segger Embeded Studio to code.
The problem I have is that for some reason, my uart don't work after using an I2C write protocol and I...
Hi,
I tried to send a packet larger than 20 bytes by calling bt_nus_send on peripheral_uart but failed.
After checked on DevZone, I found some similar problem and did...
We are having connection problems with our nRF52832 based HID device only on Windows. I've attached packet captures taken with the nRF sniffer (nRF52 DK) and in Windows with...
Hi,
I looked at some of the questions on the forum and they didn't give me good advice. Currently all I can do is nrf52832 Security 1 Level 4 and nrf52833 Security 1 Level...
Hello
I try to write functions to modify the publish and the subscribe addresses. Unfortunately not all is working, attached you will find my code.
Problems:
1.pubish...
