Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Hi,
A new version of Segger Embedded Studio is available today: V 5.70a. Can I work with this version with the nRF Connect SDK or do I have to wait for a Nordic Edition...
Can nrf21540 support all Nordic products (rf52832., nrf52840 and nrf52810)? Because nrf52832 and nrf52840 have different differential impedance specifications for the IC end...
Hi,
I want use 3 block flash. each size is 16bytes. My code as below
When I call pstorage_torque_0_clear(). I can get flag change from callback function.
but then...
I would like to use newlibc for access to math functions (logf). However, when I enable newlibc I can't get floats or doubles to print with printf when compiling for the nrf52840dk_nrf52840...
I’m using the nRF5280, accessed using pc-ble-driver (API version 6), with SoftDevice S140
I want to efficiently get the list of services from a device, including the 128...
I am using nrf52832 dev kit and soft device s132. I have use my board as an advertiser.
Like if as i put coin cell battery into the dev kit it should wake up from a system...
Hi All,
Hope you are doing well.
I am using NRF Connect SDK 1.5.0 with NRF9160 DK. I want to use P0.14 (Arduino Header Pin) as output for the RESET of LR1110 (SPI Device...
Hi, my app (nrf9160 ns, on DK 1.0 rev.; ncs 1.6.0 ) needs the port pin P0.14 as digital INput (wired on the arduino header, for a shield!!). But something is blocking it from...
Hi,
I'm writing a decoder for a custom radio protocol and I need to measure the rising and falling edges of a signal with high precision. I'm currently using the COMP peripheral...
Have been trying for hours, and searched through the forums, but no luck yet. Modem firmware doesnt seem to load with the following setup. Downgrading to previous Programmer...
Hello,
NCS1.8.0 Windows10 X64,
periodic_adv had set BT_LE_ADV_OPT_CODED and BT_GAP_ADV_FAST_INT_MIN_2 /* 100 ms */
periodic_sync scan info "Prim: LE 1M, Secn: LE Coded...
Dear Sir,
I got error like '[00:01:44.604,858] <error> app: ERROR 1813 [Unknown error code] at KGJ`hó@h:536871936 PC at: 0x0001505C' and I can't where did it happen, I...
Is SD340 v7.0.1 compatible with nRF SDK 17.1.0? https://www.thisisant.com/developer/components/nrf52832/#tab_protocol_stacks_tab
Reason I ask is on the InfoCenter there...
Hi all,
I'm working on the nrf5340 with a modified mesh light sample and nrf connect sdk 1.7.1
I'm measuring from P0.28 which is also LED1 to the GND.
After programming...
Hello,
I am using nRF5 SDK for Thread v4.1 for thread implementation using nRF52840 SOC. I have used mqtt-sn sleepy publisher as my base example to develop my software....
