Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi,
i'm new on using nRF5 modules and i have some question about how to program the nRF52840 on a custom board, so with a completely new chip.
Reading the schematic of...
I am using nrf52840 DK (pca10056) board and nrf5SDK 16. There is one low power sensor connected to the board via SPI interface. My program consume less than 30uA before I...
HI:
I transfer the init packet and firmware to bootloader successfully by UART DFU, and then the app can not start. It report error as below:
<00> info> app: Inside main...
Hi All,
My update of nRF Connect v3.3.0 failed after a while:
Update of nRF Connect failed with the following Error-MSG:
On the same day I got an install from Oracle...
Hello everyone,
I would like to use the PPK with a NRF52 Dk, but I have external sensors connected to the VDD and 5V, so when I will plug the ppk I will have to disconnect...
Hi,
I am reading a 24-bit data from SPI by getting a data-ready interrupt from GPIOTE pin in a NRF52832 chip. I have to buffer data for the BLE interval duration then send...
Hi,
I am using BLE-UART example in my project and to start advertising I am using below piece of code.
By default in the sdk (ble_advertising.c) the advertising type...
Hi,
I don't want the spm and application firmware built together so I tried using the "spm" sample in version 1.3 of the sdk. However when configuring the project i t...
I have a requirement that my peripheral device should only rely on the central to start any security operation. Right now I see a problem when the central side removes the...
I am new to BLE with my nRF51. I've got this example and I try to stop a RSSI scan when the device get all advertising data from the local device.
But when I try to add...
I burned this program in nrf9160 ncs v1.3, and how do I fix the following error?
An example can be found in the figure below
Example prj configuration see figure ...
Hi,
I would like to evaluate the NRF52811 chipset module (BMD-360 from UBlox) using the NRF52840 DK.
If I am to read the Constant Tone Extension that will be transmitted...
I followed an instructions developer.nordicsemi.com/.../gs_assistant.html in the case of Kubuntu 20.04 and developer.nordicsemi.com/.../gs_assistant.html in the case of Windows...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
I have been running some of the examples and have noticed none of the logging ever works on the Debug Terminal. I am using SES with Nordic SDK 17. When I run any of the SDK...
