Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
Hi all, I've been recently working on PSM for my device, and I've not found any resources that answer my query or provide the knowledge I need. From my reading in this article...
Hello whenever I am calling sd_power_system_off(), it gives me the following error- implicit declaration of function 'sd_power_system_off'.
What shall be the optimum solution...
I use a 3.3V battery as VDD on an nRF52832 device.
Along the line this battery might do down from 3.3V to 1.8V. Will the Internal Reference Voltage be consistent at 1.8V...
Hi,
In apply_old_config.h ,here is the code:
for example:
If I set SYSTICK_ENABLED =0 in sdk_config,here will overwrite the macro define because #if defined(SYSTICK_ENABLED...
As per the datasheet of nrf52840 any peripheral like SPI/UART/... can be configured to any of the GPIOs so is the QSPI also.
But at Pin details QSPI pins are recommended...
Hello,
We are working on machine health monitoring system. For that we are using nRF52840 SOC as Central and nRF52833 SOC as end node. We had used single Central node and...
Hello.
I'm beginner on Nordic product and checking the examples with nRF5_SDK_17.0.0_9d13099 on nRF52833 DK Board.
I tested ble_app_uart and it works. Now checking ble_app_hrs...
Hello, I am
I'm a Beginner at developing NRF 51822 My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
Recently, I've been experiencing a lot of...
Hi,
I'm trying to find a way to power down and on again a RAM section, but I haven't had any luck finding.
In the SDK examples, there's a RAM retention example only, but...
Hi! I am using nrf52832 with icm20948 (SPI) and I want to put nrf52 in sleep and wake up if there's any motion detected. I am unable to put my device on sleep by the function...
I use nrf_libuarte_async from nRF5 SDK v16.0.0, without softdevice on nrf52840. The idle power consumption of my board is several tens of uA. I call:
and then the idle...
nRF52840, SDK16.0.0, S140v7.0.1
We use SoftDevice (RTC0) and app_timer (RTC1). I'm trying to configure RTC2 and TIMER0 to do PPI-driven crystal timing as described in...
I'm using the empty_app_core project for the APP CPU and my NET CPU binary does not start. I suspect the NETWORK.FORCEOFF is holding the NET CPU in reset upon startup. I tried...
I have encrypted 12 bytes on the nrf51 and sent this + 4 byte MIC across to an Android device.
However, when I try to decrypt on Android using a Cipher with "AES/CCM/NoPadding...
Hello everyone,
I would like to developpe my own custom board, I would like to know if it's simple to replace micro USB by USB C and if someone has already do that to help...
