Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hi, I tested "Simple_coap_client" and "simple_coap_server" on NRF52840 using Threading SDK.
It seems that the route is decided by the leader, can I specify the route?
...
I am making a simple breakout board for the nRF52833 (I'm using Fanstel's BM833 module). This is what my board is looking like. There's a ground plain on the top and the bottom...
I'm trying to send data from a NUCLEO F401RE board with the nRF 52840 DK using UART. Then have the data to be sent to my phone via Bluetooth. I'm starting from the ble_app_uart...
Hi Devzone:
I have a question that may be common for companies distributing hardware containing nrf52840 chips.
I have figured out how to use nrfutil to generate Bootloader...
Hi there,
I connected my nRF5340 PDK to an external target - which was unluckily defective.
Since the external board had its own power supply, there was now either an...
Hello,
i have built my own custom service.
I have 13 characteristics ....
But in NRF Connect on an iphone, i can see 13 characteristics , but only in the first there...
Hi
Technically this is a Zephyr question, but googling the issue gave no success. Also, reading the Zephyr docs gavve me no clue.
I have a custom nrf9160 board with an...
I'm trying to capture events like accessing an invalid idx of a C++ vector
I'm using the method at , like this:
std::vector<int> my_array;
my_array.at(10000);
...
Hi,
I want to use the SAADC to measure the voltage on the VDDH pin. I am using a design based on circuit config #4 and following the SAADC example in the SDK version 15...
Hi,
I am using nRF mesh Android app version 2.1.4
I have flashed the devices with light-switch example application under nRF5 SDK for mesh V 4.0.0 on PCA10040 DK. I'm...
Hi,
I have a custom application running on a custom PCBA using the nRF52840 MCU. The Softdevice (S140, v7.0.1) is also utilised because the main application supports BLE...
Hi,
I am looking for the timing of when a connection event will happened. Radio Notification seems the right method for me since it provide an interrupt right before an...
I'm looking at the feasibility of using extended and/or periodic advertisements from an NRF52 to be received by a cell phone. I've used nRF Connect on a couple slightly older...
