Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
Hello developers, I am using nRF5340dk as my nodes and my gateway also. (3 boards).
Requirement:
i want to send my data from the board(1) to gateway with the help of mesh...
Hello,
I'm trying to configure the internal temperature sensor but have no idea ...
My board selection is raytac_mdbt53_db_40_nrf5340_cpuapp and, on nRF Kconfig GUI, I...
Hello, I am working on developing a special "serial recovery" mode dfu function of nrf52833 with ncs SDK V2.3.0. Now I encount a problem when adding the following code in...
I am attempting to get the BMI270 sample working on an nRF5340DK, using nRF Connect SDK v2.4.2, after successfully build and flash the program to nRF5340DK I got error "Device...
Hi all,
I am developing an application for a custom board using the nRF52840. I need to use the reset pin (P0.18) as a regular GPIO, configured as an input with an associated...
nRF5_SDK_15.0.0_a53641a s140 nRF52840
Documentation says that both ble_adv_fast_timeout and the ble_adv_slow_timeout are in units of 10ms, and that appears to be true of...
I have read some of the Asset Tracker documentation and noticed there is a nice implementation for operating LEDs in the UI module. This seems straightforward for GPIO control...
Hi,
We're having a problem that our application will hang when using the 32 kHz RC oscillator in the mcuboot bootloader and the Zephyr application. We encountered this...
hit there,
i am trying to work with the NRF5 SDK ARMGCC, in the IDE options a ARMGCC folder exists with an .ld file and makefile. i run the make and get the following error...
Hi,
I'm aiming to develop a custom two-wire serial interface (TX, RX). To achieve this, I'm planning to implement output capture for TX and use GPIO interrupts for RX. For...
NCS v2.7.0 and sysbuild system.
I'm looking for some clarification about Secure Boot and implementing a custom signing command.
What is the difference between secure boot...
software: ncs 2.5.0, zephyr/samples/subsys/fs/fs_sample
hardware: nRF52840 (not DK, designed by customer) and nRF52832 (not DK, designed by customer)
Step1: build within...
Hello everyone
I'm trying to build an app using Segger Embedded Studio and a nRF52832. I'm currently struggling to include the fds module since i get the following errors...
Hello,
We would like to program the external flash connected to the nRF5340 via SWD during manufacturing.
Is this possible? Do you have any documentation that explains...
