Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Are there any examples for audio recognition using Nordic Edge AI Lab audio (aka Neuton) ?
I am ready to start creating my model, but was wondering if there were examples...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
Hello
I played with the mcuboot_recovery_entry bare metal dfu sample. I noticed that if I sign an application image with an invalid key (invalid on purpose), the firmware...
I have been reviewing the antenna section in the datasheet of the BLE audio SoC nRF5340. The datasheet mentions a single-ended antenna output (on-chip balun). Could you explain...
Hi,
When the firmware is run in debug mode (J-Link connected), the system always works correctly. BLE initializes properly, and all sensors function as expected.
When...
Hello, everyone. I am an undergraduate student majoring in Mechanical Engineering in South Korea.
I am currently working on a research project to develop a PPG sensor using...
Hi,
(I'm assuming that the main() function of an application is actually executed as a thread.) I can't find any clear documentation that describes how a thread can suspend...
Hello team,
I am trying to interface the AT45DB641E flash with the nrf54l15 on a custom board. I am using the SPI00 instance.
Below is the configuration I set in .overlay...
Hi Nordic team,
We are working on a design that includes more than 50 peripheral node devices, each capturing sensor data and sending it to a single central receiver. I...
Hi,
I'd like to know how to tune the internal capacitance from the 32MHz crystal.
Specifically, I refered to section 4.12.1.1 Using internal capacitors in the nRF5340...
I am using the nrf52840 in QFAA package, and the external DMIC example receives audio data through the PDM interface. I noticed that the official documentation mentions support...
Hello,
We have been testing/validating sQSPI on nRF54L15.
We tested the sQSPI on two versions of our nRF54L15DK (0.9.2 and 0.9.3).
We are using this sample app: https...
Hello. I have one question.
When configuring RAM with the nRF5 SDK + SoftDevice, if I get the following error: APP_RAM_START=0x20006000 --------------------------------...
Hi,
I'm trying to program the nRF52840 Dongle (PCA10059, 2.1.1, 2023.26). I modified the Bluetooth: Central UART sample to use USB instead of UART and built it for the dongle...
I need to use one IO port of the nrf52832. This IO can not only detect the ECG signal but also achieve system off wake-up. The ECG signal is a PWM signal with a duty cycle...
