Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi,
I followed the instructions for enabling mcuboot and OTA using DFU target APIs using the instructions here -> https://academy.nordicsemi.com/courses/nrf-connect-sdk...
Dear all
I am developing a product using the nRF54L10 with the Zigbee add-on v1.2.0. I have a question regarding sleep behavior.
The current measurements below show the...
Hi,
I am developing an application with the latest available version of the nRF Connect SDK (v3.1.1) for the nRF54L15 SoC.
I want to develop an application with B0 + MCUboot...
the existing code is using freetos, and main.c finally ends at
which never returns as expected... but my ble scan and advertise do not appear to work, no events...
Hi,
I'm working on a four layer PCB including the nRF7002 for WiFi location finding. After looking at the various Altium Design files available (Thingy91X, nRF7002Dk, nRF7002EK...
I want to test the nrf21540dk to compare range improvements over the nrf5340dk and nrf52840dk. I am using the hci_pwr_ctrl demo and want to adapt it for the nrf21540dk. I...
Hi — I’m working with two nRF5340 Audio DKs (one as server/gateway, one as client/headset). When the nRF5340 server uses standard BLE Audio (CIS/ISO + LC3) it connects and...
I am trying to get the hci_pwre_ctrl demo working with a nrf5340dk using nrfconnect 3.1. I got it running with a nrf52840dk and it works fine. I created a 2nd build for the...
Hello Nordic Support Team,
I am currently working with the Arduino Nano 33 BLE (ABX00030) , which features the nRF52840 SoC , and I am interested in accurately measuring...
I want to read the RSSI. The code is shown as follows: ，However, after compilation, the error message displayed is: "undefined reference to `bt_hci_cmd_alloc'".I need to know...
Hi there,
I am seeing inconsistencies with the PCB layout specification of the nrf7002.
1) In the v1.1 of nrf7002 datasheet, it is recommended that the following capacitors...
Hello, we are currently testing the output of square waves through GPIO output pins. However, I found that a single operation to set the GPIO output pin high or low using...
I've installed the same version of the Power Profiler V4.3.1 on Linux and on windows.
On windows the device gets recognized straight away and I can use it, on Linux however...
If I understand correctly, you can pretty much assign any pin to any peripheral. I've been using a modded central uart project on a dev board but on this other board I'm using...
Hello,
is there any way to access the Stack and Heap Start/End memory addresses from the zephyr code?
I have found the __INITIAL_SP definition that gives the Stack start...
