Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello Sirs,
I loop typing the same command program:
clear>tart_channel 02>output_power pos0dBm>start_tx_modulated_carrier>cancel
After repeating the same instruction...
Hi,
Project development using board with HL7800 modem similar to Pinnacle 100 did not succeed with FOTA upgrade so it is been decided first to try it with nrf9160dk_nrf9160...
Our product consists of a Texas MSP430 and a Nordic nRF52832 Chip, with serial/UART between
for MSP programming, debug and development : I'm using the official TI MSP-FET...
I am testing programming secure bootloader. But J-Link Commander reports Could not start CPU core. (ErrorCode: -1) after programming softdevice, bootloader, and application...
Hi,
Now I'm going to use 52833 USB_CDC_ACM , but there is no suitable type in SDK17.1.0. It's just have pca10056 . So I port to 52833 based on the 52840_pca10056 routines...
Hi team,
I am using nRF52833 DK with PCA10100 on it.
I am developing app_timer application for blinking led for a fixed time interval. But it is not working properly....
Hello,
We are trying to adapt the simple_gw example to receive temperature measurements from a zigbee temperature sensor. However we do not succeed. We can find the device...
I'm using an nRF5340 DK board with ncs v2.0.0. I have to build an application that should access BLE running in the network core. I see there are two options provided, Remote...
Dear Nordic engineers
I have a probelm would like to ask you.
I read this link: https://infocenter.nordicsemi.com/index.jsp?topic=%2Ferrata_nRF21540_Rev2%2FERR%2FnRF21540...
Hello，
I am developing an AoA Tx project using NCS v1.9.0 & 52820. Some problems are hard to solve by myself.
Below is my configuration:
1.When CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC_CALIBRATION...
Hello,
we are using the "AT%CCLK?" at it works very nice.
but now for the challange... since the modem is synchronized with the LTE network and sends on the designated...
I notice a problem with the MCUboot Hello World example.
I followed the steps mentioned in https://www.mcuboot.com/documentation/readme-zephyr/ That is, build the MCUBoot...
