Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
We'd like to evaluate the nRF9160 for our device as a replacement microcontroller + LTE-M modem.
Working with the DK should be fine for evaluation purposes, but in the end...
I do the install by step , https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing.html
the toolchain install failed when on step 5;
log as belowed...
Hi All,
I am currently implementing Write communication, referring to ble_app_blinky in example.
When the phone gives the command, the program will run this function,...
I'm attempting to control a PA attached to an nRF52840 in a way similar to Case ID: 212504
But I'm also using Zephyr...
Are there equivalent calls available via the Zephyr...
Hello，
We are using NCS v1.9.0 and nRF51820 SoC in our project.
Here is a question about using the COMP function.After I configure and initialize COMP，it returns NRFX_SUCCESS...
this is ADC config
This is the electronic schematic
Q13open，CURR N1和CURR P1 get parameter from temperature sensor 。OUT1 is temperature sensor ，it was 0.5Ω...
Hi,
i am working on nrf52 dongle. i want to use ble_app_uart example with it. how i can receive data on uart with usb. i can send data on ble but not receiving on uart....
I want to creat a hci vendor-specific command of zephyr using nRF connect SDK, based on hci_pwr_ctrl bluetooth sample.
At first, I think just using follow steps in hci_vs...
Hi,
Recently I have heard that there are license restrictions on using DKs for production programming. Is this only for production programming? Can I still use the DK to...
Hello, im trying to implement the UARTE Driver for simultaneous Use of Bluetooth and asynchrounos Uart TX/RX on a nRF52840 and nrf9160. The Problem is that neither RX or TX...
Hi
i want use a nRF52840Dongle as a Zigbee end device, when power up, i get following message:
I: nRF5 802154 radio initialized ***** delaying boot 5000ms (per build configuration...
Hi, I have just started evaluating nRF52840 using the dongle and Development Kit. I have successfully tested the Openthread network using CLI project. Now I want to try out...
Hi experts, The situation is following, the NRF53 shall receive multiple packets. After the reception of one of the packets the next one shall be received at the same frequency...
