hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
On Zephyr `2.7` I have following code to setup a SPIM on a custom board: Device tree:
main.c:
Now this no longer works on Zephyr `3.1`. I temporarily tried it with ...
Hello
I tried to install nRFConnect for Desktop, the latest version When I try to launch Toolchain Manager, I get an error "Unexpected end of JSON Input" error message....
Hello,
I works with Zephyr, VCS, SDK 2.0.0
I don't find how to get pin number from the DTS pinctrl .
In this folowing code, I want to replace magic number (uplighted...
Until toolchain update it was working well. But after toolchain update I cant even open toolchain manager . It just shows some exception like " Unexpected end of JSON input...
using NCS 1.9.1 - Zephyr - Segger Studio - sample code: bluetooth / peripheral_uart
I based my project on the sample, modified it slightly and it works well on a board with...
Hi,
I saw here: nrf52840 802.15.4: mlme_start_req: nonbeacon-enabled mode doesn't work
that the SDK-Version 14.2.0 was not compiled to work with non beacon enabled mode...
Hello,
After upgrading to the new version with the help of the migration guide, there is an issue that I could not trace back to any changes.
If I am correct its about...
Im compiling an app in nrf sdk 2.0.0 which works well on the nrf52811
as soon as I add
CONFIG_NRF_802154_RADIO_DRIVER =y
into prj.conf
without even initializing...
Hi Everyone,
I am working on NRF52833. I have developed code for our project. Now in this project the phone app will connect with the device using BLE for which I have implemented...
I have a Nordic Thingy:52 and Nordic Thingy:91, and I want to develop custom embedded software for them. Do I need a J-TAG or can I flash code using USB?
I've seen tutorials...
Hello,
I'm starting development with nordic arm processors. Therefore we purchased the BMD-360 EVK. This board features the NRF52811 processor and has the same pins as the...
We currently have a nRF52840 central device written with the Bluetooth Nordic SoftDevice API. From what I have read, the Zephyr RTOS is the best way going forward. I started...
Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello ,
I on the DK nRF52840, I wanted to manage the sleep mode and measure the current consumed by the microcontroller.
I started with example uart, I cut the PCB track...
