Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Thanks in advanced. I'm using nrf52832 with nRF5_SDK_17.0.2. I try to measure adc time consuming as below:
I find when timer sample rate is 500ms, then adc time consuming...
Hi:
I am doing a project which will use both PDM interface and bluetooth transreceiver, PDM interface is used to receive audio data from a MEMS microphone and Bluetooth...
We have a design that uses a simple custom board with an NRF52832 chip, button, accelerometer and onboard battery. For many phones, the operation is quite stable - we connect...
Hello all:
I've developed an nRF52810 application based on the UART example, but when I include buttonless DFU support to my application, it doesn't work. I'm using SDK...
Hi,
now I had achived the function to communication using the esb in nrf52832 that one to one,but I need to achive multi tx device to one.
if there not doc for me to achive...
Hi
Strange that there is no example for such popular code which will allow changing the iBeacon setting parameters (like: name, power, interval etc). with a smartphone application...
Hi everyone,
I'm trying since a few days to connect the Thingy 91 to the network with any result at all.
This is my configuration:
Modem firmware: V 1.3.0
Application...
Hi,
Am trying to store the data fetched through ble scanning to the flash memory of the nrf52840 DK. So I have been making use fo the flash_storage example in the SDK/examples...
Hello,
Our Peripheral server application regularly uses a stream of notifications to transmit data to a Central client. We have a rare error in which sd_ble_gatts_hvx returns...
app time loop update 200 byte data use fds by 10s ,then after many time error happened, update_user_flash is update API, write_drop_record IS loop write API in app time, ...
When running in High Voltage mode, it specifies a maximum of 7mA of external power draw on the Vdd output. It also specifies the voltage accuracy of -10%/+5%. This is a very...
HI devzone
Everytime after i executed "nrfjprog -f nrf53 --recover" on nrf5340 DK
i see it write around 4KB data into the flash. do you know what is the meaning for this...
When writing to flash it is MUCH easier to perform the write if SoftDevice is disabled. If it is not, one has to wait for an event to continue writing. ON the Nordic platforms...
Hi,
Is it possible to set the USB serial number for the nrf52833 and nrf52820 MCU's?
For the nrf52840 I've found this documentation: https://infocenter.nordicsemi.com...
I want to try Zephyr on the nrf52dk_nrf52832. (PCA10040)
I can not get it to work.
If I try to use -DBOARD=nrf52dk_nrf52810 All is OK
Here is what I do:
cd ~/zephyr_test...
