Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi, I am try to implement UART SERIAL Bootloader for my device and I just need to perform DFU using uart serial
I have tested the code and bootloader. My query is
Without...
When I run the "ble_app_blinky_pca10040_s132" example from SDK 17.0.2 and 15.2.0, right after Connected I'm seeing that device is Disconnected from device.
I tried with...
We need to programatically (on the Raspberry Pi using Python) send and receive characters to and from a smartphone using a custom service over BTLE. I have used the blinky...
I am trying to communicate with my IOT using wired uart serial port. I am using 840(MCU) (with softdevice #113).
code:
My Issue: Each time I am trying to run it while...
Hi,
I am trying to reduce the consumption of my Thingy91 device in idle mode. I am working with NCSv1.3 and the example asset_tracker. I am currently registering 0.60mA...
In our NRF9160 application, we do not have a UART available and have to implement other means of logging crashes.
We have written our own k_sys_fatal_error_handler but it...
I am using a generic nRF52 dev board with the Arduino nRF52 core . I am trying to get a sample BLE service to display, but it cannot find it on my BLE scanner. After I couldn...
Hi,
I am trying to read read all nearby base stations' Cell ID, TAC, MNC, MCC.
Is this even possible to do with this DK?
At this point I have found these commands...
Hello,
I am trying the UDP sample for the nRF9160 DK board, using the iBasis SIM card that came with the kit.
The problem is that it does not register onto the network...
Hello,
I’m trying to interface the MAX32664GWEB+T sensor hub with the NRF52 by using I2C, I’m wondering if you could provide me any recommendation, libraries or codes for...
What I want to do is do UART communication (UART_1) between nRF52840 and nRF9160.
From the nRF52840 side, uart_poll_out is OK, From the nRF9160 side, uart_poll_out examined...
Hi Nordic team,
We have planned to use nRF5340 based BLE mesh device which is interface with sensor
We would like to transfer customized user data from one node to another...
I tried different nrfconnect examples and noticed that: C:/Nordic/v1.4.1/zephyr/samples/basic/blinky/build_nrf9160dk_nrf9160 blinky: rebuild solution + flash: OK also hello_world...
HI,
I am working NRF52810 with SDK 17.
I am able to pair my nordic device to mobile. but after pairing I want to send some data/receive some data.
how can I achieve...
In SDK 17.0.2, most places it looks like BLE_GAP_ROLE_CENTRAL is allowed to be undefined, except in nrf_ble_gatt.c line 142. Was there supposed to be "#ifdef BLE_GAP_ROLE_CENTRAL...
