hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I want to encrypt with AES-256.
I want to use the following two functions.
mbedtls_aes_setkey_enc mbedtls_aes_encrypt
I want to add a library containing ncs/v1.4.1/mbedtls...
Dear Support team,
I used PPK2 to test the PSM mode current of nRF9160 is about 7.09uA (as shown in the figure below),but the eDRX mode current has not been tested successfully...
Hello everyone,
I am going tp establish a mesh network by using a devkit and two or more dongle. take as an example, turning off a led on the dongle boards by using a bottom...
Hi, I'm using code based on sdk/components/libraries/bootloader/dfu/ for ECDSA verification of the signature. But switched to Oberon crypto backend. The signature was successfully...
Hi,
I'm trying to convert the NCS - cloud client sample to connect to AWS_IOT rather than NRF cloud.
After a connection achieved, i press Btn1 and I get the following...
I believe I am having a very similar issue to devzone.nordicsemi.com/.../dfu-from-external-flash-using-spi-nor
I posted this as a new thread to avoid high-jacking that one...
Hi everyone,
I am working on USB MSC example . I have two questions.
1. What is the MSC_WORKBUFFER_SIZE defines in the example? Is the last parameter of APP_USBD_MSC_GLOBAL_DEF...
My issue seems to be similar to DRGN-12539. However, I am erasing internal flash.
I am calling in a loop nrfx_nvmc_page_erase to erase multiple pages of flash. At first...
I am building a custom boot loader to work with out application on a custom board based on the UBLOX NINA-302 module. The boot loader will use USB as the only connection and...
Hi.
I'm trying to read data of MAX30102 using TWI, it has 8 bits of data in the FIFO_DATA register.
The library I'm using for data extraction and processing was written...
Hello,
I am using the nRF52 DK with Segger Embedded Studio and the SDK 14.2.0. I wanted to build the example 'esb_ptx_pca10040' with logging enabled. To achieve this, I...
Hi,
I'm using the S132 on the PCA10040 with the external XTAL disconnected (SB1 and SB2 cut)
In order to check to if the external is present I call nrf_sdh_enable_request...
