hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Dear all:
I found that the nrf52840 flash size is only 1MB, but the size of light bulb load is about 850KB, I have some questions:
1. Does it contains the FOTA region...
Hi
I am trying to use nrf52811 using nrf52840 DK board.
First, I check simple GPIO example working on my nrf52811 based custom boards
Second, I checked the Bluetooth...
How can I execute a command to commission a device for Thread by using the QR code or pairing code? (without using the pin_code or discriminator) Thanks.
Hi I want to run an epaper with the nRF52832 therefore is SPI needed. Board file was generated from scratch. In the devicetree I added the SPI modul and a epaper modul, which...
Hi,
I am seeing a strange issue with nRF52840 Dongle when I run a custom BLE connection test repeatedly. Below is my configuration:
FW in nRF52840 was programmed using...
Hi,
I'm learing how the i2s streaming works using the example "echo" under "ncs\v2.3.0\zephyr\samples\drivers\i2s\echo". I have a prototype board with nRF5340 and the audio...
When flashing the chip with a build from the samples/bluetooth/hci_uart via west build -b nrf52840dk/nrf52840 samples/bluetooth/hci_uart --pristine and west flash off the...
Hi,
Is it true that you can not disable the nRESET pin in any way? (So that the MCU does not reset after nRESET being pulled low.)
I've gone through the documentation...
Hi Team,
We are using SDK 2.5.2 with MFW 1.3.5
We need to download a secure file from amazon, we first tried to download file from public server connecting to port 80...
Hi DevZone,
My customer found that when using the NRF5340 PDM, there is significant attenuation if the incoming audio signal is a 2kHz signal.
Upon checking the specifications...
Hi DevZone! I am developing a Bluetooth beacon that needs to use extended advertising due to the need of periodic advertising. I am using custom board with nrf52820, nRF Connect...
The following phenomena have been observed in an anechoic chamber:
Success : After the bt_audio_stream_start function is called, the stream_started_cb callback is invoked...
Hello,
We applied for some nrf9151 samples and designed a simple development board with reference to nrf9151 DK. However, there was an issue during testing that the SIM...
Hi, I'm having problems with the firmware update of the Thingy-91. I received it from my professor to use for my final project (it has already been used by previous students...
I am developing a Github CI pipeline to automatically compile, sign, and upload firmware images for a nRF52840 device.
Because I don't have direct control over the machine...
