I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hello,
I am after an example for nRF5340 showing how to use RTC to wake up from sleep.
I have a couple of timers running few tasks at regular intervals in a forever loop...
Hi,
When building the Onomondo softsim_static_profile sample using nRF SDK 2.6.1 I get a region `FLASH' overflowed build error for mcuboot_subimage.
c:/ncs/toolchains...
Hi,
I'm seeing a slow and odd scanning behaviour since I updated my toolchain and NCS to 2.6.1.
To my setup:
I have two NRF52840, one acting as peripheral, the other...
I have a customer who developed against the Zephyr HCI example ( https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/bluetooth/hci_uart/README.html )
I assume...
Hello,
Currently, I am working on a device that has multiple sensors connected with nRF53. Each sensor collects its own data in its thread. Some sensor threads are related...
Hi,
I wanted to use the bme68x_iaq example as basis for a new project.
However, looks like parts of the support files in Zephyr aer missing because it stops with following...
Hello, we are testing the LPUART example in loopback with a very simple circuit. The carrier module is PAN1780 - nrf52840 on a custom board with no other things connected...
Hi,
I am using the nPM1300 in combination with a STM32L431KBU MCU.
Also the code from Nordic to communicate with the nPM1300: https://github.com/NordicSemiconductor/npmx...
Hi to all,
I'm developing a beacon application on the nRF52840-DK starting from the example that I found in the VS Code (Zephyr).
I'm designing a custom board with only...
Hi,
I just started developing a BLE Central device on a nRF52840 DK. After successfully connect my DevKit with a phone acting as a peripheral (using nRF Connect Mobile)...
Good Day
We have an issue where our device will run normally in a full load condition for about 2 hours without issues but will suddenly go into the app_error_fault_handler...
I am facing heap memory issues in my code. I am using dynamic memory allocation for saving microphone data into sd card. Along with this I am using wifi also.
CONFIG_HEAP_MEM_POOL_SIZE...
Mirroring the issue from Github here I'm working on an application with timers and PPI. Today I discovered that when using the function nrfx_timer_extended_compare with a...
Hi ,I am new to nrf .I am currently using nrf5340,so i want to just print raw data of sph0645 using zephyr.I tested with examples of echo but i didnt achieved to print raw...
