Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I'm trying to do an ADC measurement on AIN6 on an nRF52832. This is how I have things set up:
proj.conf:
Overlay file:
ADC initialisation (this gets called on power...
Hi Support Team
We are testing the sensing of zephyr sample in the below directory with nRF52840, but we can't find which callback function is used to get the sensor data...
Hello,
Im trying to update the custom nrf5340 board over BLE. I have managed it using nRF Connect and Device Manager.
I can upload it using nRF Connect, but I need to...
I am developing a firmware for nRF52810.
Does Zephyr support debounce care for push button switches in ncs v2.6.1?
It seems that CAF supports it, but I don't plan to...
Hello!
We are on the process of implementing our own desktop program to run DFU over BLE, similar to how the nRF Connect application does it. We are using SDK 17.1.0 in...
Hi,
I am using NCS v2.4.2 and nRF5340DK + nRF21540EK but I can not enable GPIO+SPI mode.
for example, I use nrf/samples/bluetooth/central_and_peripheral_hr application...
I am working through BTLE Fundamentals, Lesson 6, Exercise 2, and running the code from blefund_less3_exer2 per the instructions and it all looks good on the app COM log:...
Hi ,
I would like to know if we can use 2 PPK's in such way to measure both direction.
As you can see in the diagram , the current can flow to the battery or can flow...
The bluetooth program refers to app_ble_uart. Bluetooth uses nRF52840. I use stm32 MCU to transmit data through UART. The baud rate is 460800 for transmission. The UART transmission...
I am using nrfConnect for Visual Studio Code 2.6.1 and I am being asked what version of Zephyr I am using when diagnosing a problem in a Zephyr forum. There has to be some...
Hi
Seems like all new nRF DKs shipped with nRF5340 as interface mcu have limited speed on Debug Out.
nrfjprog -r --clockspeed 646 Applying system reset. Run. nrfjprog...
I need to send a JWT to a non-nordic server. They ask for a small struct to be encoded and sent as a string in a larger MQTT message. For example:
That struct is encoded...
I have flashed the light_ctrl hex file in nrf52840 dongle. Flashing Have been completed sueccessfully for provisioning in nrf mesh application its not showing in the network...
Hello,
For a Uni Project I want to measure the current of the Nordic Thingy:91 and visualize it. Therefore i bought the Power Profiler Kit 2. But i dont know how to connect...