I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I am using 3.2.1 SDK and I am using zephyr in VS Code
I am trying to get the NearBy Interaction working. I have both an IOS and Android phone and I have not been success...
We are using SDK 3.1.1 and nrf52DK with our own Model ID and anti-spoofing key from Google.
When flashing the Locator Tag example to the board, a half sheet notification...
Since the product we are developing is supposed to experience extremely high temperature conditions, we are concerned about the ambient temperature operating limit of 85 degree...
Hi Nordic Support Team,
I have created an issue on GitHub regarding the device type ID error we encountered during testing. Here is the link to the issue:
github.com/...
Hi,
I am getting started in a project where I am using the nrf52840 dongle to develop. One of my goals is to keep the toolchain up to date, so I started working with the...
Hi Nordic team,
I am working on BLE Channel Sounding (Initiator + Reflector) on nRF54L15 using Zephyr / nRF Connect SDK v3.1.1.
I would like to clarify the expected behavior...
Looks like the new project behavior changed between 3.2.0 and 3.2.1. When creating a new project with the copy function, in 3.2.1 it no longer copies the source code to the...
Hi Nordic
i am working with nrf52832 and nrf52840
After migration from ncs2.9.2 to 3.0.2 my device (end point) has an issue with pairing to one of the gateways (the gateways...
We have an issue receiving unicast packets with default wifi low power mode.
When CONFIG_NRF_WIFI_LOW_POWER=y is enabled, unicast packets (DHCP Offer/Ack, DNS responses...
I performed the following steps:
1. I installed nRF Connect for VS Code Extension Pack in VS Code
2. I created a new application by copying a sample (Bluetooth LE HIDS...
I'm building my small board with nrf52810, buyed 10 chips from seller, it is cheaper relatively, I know it is used chip.
7 of them burned successfully,but 3 of them raise...
I am having difficulty getting Thread Block-wise Transfers working correctly using the API from NCS v2.0.0. It was my understanding that the otCoapSendRequestBlockWise function...
Hello,
I'm implmenting firmware updates over BLE, using a nRF5340DK, nRF Connect SDK v3.2.1, and an Android phone.
I can use the nRF android app, but how can I do this...
