Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi, I am devolping a sensor system where I am in need of a Tri state GPIO solution
Currently using the NRF54l15DK with all the latest software versions (3.11, etc.), developing...
I am trying trilateration for indoor positioning system with nrf54l15 , using 3 initiators and a reflector I was not able to switch between initiators and also one of the...
Product is a zigbee router.
Use nrf connect sdk 2.4, update it is not an option.
The zigbee join work fine most of zb3.0 coordinator, BUT with an old coordinator it failed...
Hi all,
I'm using aws iot lib and last will topic feature, everuthing works but I have a question, in prj.conf I set my topic with
Is it possible to build this last...
Hello Nordic Team,
We have developed a custom PCB using nRF9151 and nPM1300 . In our setup, sometimes the PMIC powers up and works correctly, but other times it does not...
Hello, I am using Nordic chip 82832 with sdk 17.1.0 and SoftDevice s132. I am facing an issue where a specific requirement requires my advertisement interval to be specifically...
Hello,
we would like to use the LPCOMP on the nRF54LM20A, but there's some confusion on which GPIO domain can be used.
According to the overview block diagram , LPCOMP...
Hello,
I'm working on a custom Zigbee End Device application where I want do some modification of the device announcement message. I've used NXP's Freescale Beestack Zigbee...
In Nora B-206(nrf54l15) not able to use port 1 pins 2,3 (P1.02/NFC1 P1.03/NFC2) as normal GPIO. TRIED :
& nfct {
status = "disabled" ; // Disable NFC to free P1.03 for...
Hi,
I'm using a custom code I developed to save all console logs to an SD card based on the Zephyr architecture. I originally developed it for the Thingy:52 and have also...
Under the old `nrfjprog`, it was possible to check whether the modem firmware matched a particular release by running `nrfjprog --verify mfw.zip` (see )
This is no longer...
Hi Nordic support:
We previously submitted a case about OTA testing in CMW500 connection mode. Following is that case:
We tried OTA testing with the CMW500 connection...
Hi everyone,
I’m starting a new project using the nRF54L15 MCU . I’ve worked with the nRF52840 and nRF52832 before, but this is my first time with the nRF54 series.
Due...
Hi,
I am using NRF52833 with soft device version s140. I have set the advertisement duration for the BLE app to 0 (meaning the duration is infinite). Also, I have set scanning...
Hello Nordic Support Team,
I am working on a project using the nRF52832 microcontroller with NRF5 SDK version 13. I have implemented the Flash Data Storage (FDS) module...
