Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi everyone, I use nrf52833 to make dongle. My test found that after suspend of usb, I tried to enable ESB rx mode, but I couldn't receive rf data. What is the problem?The...
Hello,
When deleting a bond from the central, after trying to reconnect with the peripheral the PM_EVT_CONN_SEC_CONFIG_REQ gets called as expected. I know that allow repairing...
I have been trying to develop a project, my custom board has a nRF52840 chip and I have a nRF52840 DK too.
My problem is when I try to debug any example from any SDK....
Hi, I attended the Nordic Seminar in Tel Aviv last week and heard several lectures from your experts.
It was recommended that we use a module with Nordic IC rather than...
Hi,
I am using vscode and nCS on windows, kindly help me with below 3 queries:
1. How to generate a binary signing key, say "KEY_1"..?
2. How to sign a binary with...
Hi,
We are trying to use PPK2 to measure current of our board, we want to receive the data from PPK2 and parse by our owner python script, so could you provide the protocol...
Reading The adhoc smart waste solution uses the nRF9160 SiP I tried to reproduce the mention 6 µA with LTE-M in eDRX with an interval of 655 s.
I use
CONFIG_LTE_EDRX_REQ_VALUE_LTE_M...
Hi,
We use PPK2 very conveniently as a logger for testing.
How about adding the supply voltage as display options also?
We hope you will consider this.
Thank you...
Hi dear,
It is possible to establish parallels multi connection to different J-LINK's devices serial numbers via nrfjprog.dll, or any other automated way ?
We successfully...
Hello, I'm making a breakout board with nrf52832 qfaa. I used chip antenna (2450AT18B100E) and followed Nordic reference layout. I am getting around 60m range in an open environment...
run nrf Connect for bluetooth Low Energy Standalone
connect PCA10040 board
select "server setup"
press "+ New service" which adds a New Service
press "> New Service...
Hi, I am currently learning to retrieve location using thingy 91 and location example from nrf SDK. When I run it, I got this message (below).
After doing some research...
I want to change the data in the registers of Radio peripheral when the Radio at the state of "Disabled",but with no respons.
Only if I repower the Radio it works,but why...
Hi all !!!
I am trying to program the bootloader and softdevice using the J-Flash software, but I get this error, how can I fix it?
Board: PCA10056 (NRF52840)
SDK: 17...
