Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello all,
Currently, we are using the nRF52840-DK and realized that the interface to upload programs is very handy (being able to simply drag a .hex file onto the device...
Hi,
after updating my NCS version to v2.1.2 I noticed that my Zephyr SDK also needed updating from 0.14.1 to 0.15.1. However, after updating my Matter project does not compile...
Hello,
When using two nRF52832 modules for Bluetooth connection, can it prevent Dos attack program? We have found a situation where a malfunctioning or malicious client...
Hi,
I am evaluating the nRF5340 Audio DK and measuring while adjusting the audio bitrate.
I found the following 3 symbols definition for bitrate.
CONFIG_LC3_BITRATE...
Hello
I got a nRF52840 DK and try to use Direct Test Mode APP (v2.0.3) in the nRF Connect for Desktop (v3.12.0).
However, it always says "Can not communicate with device...
I have sdk 2.1.0 and nrf5340, trying to run peripheral_uart sample connecting nrf5340 to a module via uart. The program seems working when only works with nrf5340 based on...
Dear Nordic Support Team,
I wanted to configure the nRF52840 dongle as radio co-processor. For that I wanted to build and flash the Thread: Co-processor sample in nRF52840...
Good day
I intend to use a power saving mode to turn on a device for a set amount of time. During this, the device would still need to receive commands over mqtt. Is this...
Dear SRs
We are evaluating your NB-IoT solution by means of Thingy91 reference board. The NB-IoT service is working with iBASIS card, the question is: can we change the...
I've created the samples for Socket Echo Client https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.0.2/zephyr/samples/net/sockets/echo_client/README.html#sockets-echo...
HI , I am having difficulty in interfacing the flash with my DK board
1) The spi flash sample is getting stuck at flash erase function without any error responses
2) I...
I see this case mentions constant tone extension. Currently, only nRF52833, nRF52820 and nRF52811 can do this.
https://devzone.nordicsemi.com/f/nordic-q-a/59948/nrf52-selection...
Hi,
We're working on a development project using nRF52832, SDK 15.2 and s132_nrf52_6.1.0_softdevice. I'm trying to use the radio test example from the SDK to certify the...
Hi all,
I have a board based on an nRF52832. At the moment I program it through the nRF52 Dev-kit (with the debug out connector) as my board doesn't have any debugger...
I'm a complete idiot when it comes to Nordic, this is literally my first time experience with any Nordic chips. I have a little experience programming ESP32-s3 chips, and...
