Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
HI,
We are looking to multiplex a few I/O on the NRF52840 to save pin count on a header. If D+ or D- get driven when VBUS is unpowered, will that damage the NRF52840? Or...
Hi there,
I think that I am seeing the repercussions of errata item 136 in my application. I abruptly turn on/off power several times to my board, and every once in a while...
Hi,
On my bl653_dvk board, I am running the ADC example. It functions properly. I have a few questions about this:
1. How to determine which clock is being used by the...
Hi everyone,
I want to send large data with https protocol.
I edited the https_client sample split the data and looped send() for sending the large data.
But when...
I am working through the https_client example with the nRF9160 and I noticed that when Connection: close is not included, the connection doesn't close, but if I attempt to...
Hi,
I'm sending values over ble. On the client side I opened an serial monitor. Everything seems fine. The values are received in the right way.
But when I try to read...
Hi,
I have previously used the ESP8266 WiFi module and it has worked great. Since I have updated to the latest SDK, I am now seeing problems. I'm guessing something has...
I am currently working on enabling and transmitting/receiving data using TWIM on my nRF52810 development kit. The documentation states that in order to enable TWIM I need...
Hello,
I told my students to set up an SPI bus with several peripherals. We found nice development boards with a screen and a card reader sharing MISO,MOSI,CLK and one CS...
Device: nRF52840 Softdevice: 140 SDK: 17.1.0
I'm trying to develop a custom bootloader that will determine which of two images (A or B) to jump to. The memory map that I...
I noticed that if I set options = BT_LE_ADV_OPT_NONE in bt_le_adv_param I get a random address at each bootup and if I set it to BT_LE_ADV_OPT_USE_IDENTITY I get always the...
Hello,
I'm currently working with ISP2053 which is the nRF5340-based module.
The system, as the specific GPIO pin detects a low-to-high event, gets data from another...
Hello guys,
I'm trying to run uart example from https://github.com/andenore/NordicSnippets/blob/master/examples/uart/main.c extended by interrupts call after transmission...
Hi.
I cannot build a ble_app_uart Nordic example that I was able to build flawlessly three years ago and later. I wonder if anybody could give me a clue on what's going...
