Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
We are implementing a system where diagnostics info is saved to FLASH when one of the error handlers is called. Our code collects diagnostic registers and stack info, and...
Hello,
I am working on a driver in which it needs to transfer larger sets of data over a I2C connection. However, I am getting this:
"Cannot copy flash buffer of size...
Hi，
Q1: SDK for PCA10112:
I'm trying to evaluate 21540 DK and EK set. Where do I get sample code that compatible with PCA10112? I've checked the latest nRF5 SDK 17.1...
There are several questions regarding this, most recent I could find from 6 months ago ( https://devzone.nordicsemi.com/f/nordic-q-a/81686/is-there-support-for-gatt-caching...
Hi,
I would like to know if I can update the firmware of modem from 1.1.1 to 1.3.1 on Thingy91 (hardware version 1.4.0).
My goal is to use AGPS and PGPS assistance services...
The product specification states that "o nly the dedicated QSPI pins shall be used. " Is this a recommendation or a requirement? I would like to configure a different pin...
I accidentally closed the original ticket , so I create a new one.
Hi,
recently I'm building dfu function on my board, using nrf51822 qfaa and softdevice s110.
...
hello,
Im using nrf52840 Im trying to emulate a chip select signal for spi slave with gpiote and ppi. I used an active high signal as an event and a signal(cs) that is toggled...
Hi everyone,
I have some questions regarding RSSI:
1. Is there any Bluetooth reference that evaluates the RSSI? For example what RSSI range is considered as perfect, moderate...
env:
SDK: nRF5_SDK_17.0.2_d674dde
KEIL- ARM
SoftDevice： s140_nrf52_7.2.0_softdevice
i can't understand how MBR jump to bootloader, and how MBR konw the start address...
I'm using SDK 17.0.2 and I'm trying to write a small central device. It should connect to a single peripheral and exchange some data.
Once the peripheral is found, central...
Hi,
I am trying to get access to the code 1.99.99-dev1 branch of the NCS, but I'm not sure where I can find this. More specifically, I would like to use the code of the...
Hi.
I am developing a small notification monitor.
It used a 150mha battery and a 0.92 oled.
I want it to be connected to my phone via Bluetooth and when I send a string...
Hello DevZone,
I have a project where I want to use NFCT for communicating and charging. I have used the NRFX_NFCT library to read and write to my transmitter because...
