Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi
We are using the nRF52840-QIAA-R in a lot of PCBA, now I see there is a new revision nRF52840-QIAA-F-R and the old type is not recommended for new design.
What is the...
Hello! Sought out to upgrade from NRF SDK 3.1.1 to 3.4.0 today so downloaded and installed it on Mac using nrfutil sdk-manager command line, and that was fine. The project...
Hi,
In our PCB using the nRF54L15, we used different P2 pins for the sQSPI, believing after reading the docs and driver API, that one could configure different pins than...
Hello Nordic Support Team,
I am testing nRF9151-DK board. I wanted to debug an application that is created when "Create a blank application" option is chosen from nRF Connect...
Hi everyone,
I am trying to use P0.0 but it keeps getting uninitialized when calling nrfx_spim_uninit.
nrfx_spim.c line 659 keeps uninitializing P0.0
It is because...
Our device is using NRF54L15 for BLE function. When we test the max distance of ble connection between 2 devices, we get the below results.
We are confused by these...
Hi Nordic Team,
I am working on a custom device based on the nRF5340 SoC . My application captures live audio from an I2S microphone , processes the audio on the nRF5340...
Goal: Create SBOM with correct version numbers, CPE search strings, PURLs, and licenses. Use that to scan and assess vulnerabilities. Platform: NRF Connect SDK 2.9.1 or newer...
we run long-term HIL tests with typically 3–8 nRF9151 DKs:
DKs spaced only about 1–3 cm apart
short USB 3.x cables to powered USB 3.2 hubs directly below them
sometimes...
This is a product based on nRF52832, which uses PA/LNA.
The device resets in Bluetooth advertising state. the ID is 1 (NRF_FAULT_ID_SD_ASSERT), the PC is at 0x000071CC,...
Hi Nordic,
We are developing a PC application for product programming that uses nrfutil to program the nRF54LM20. The programming process involves recovery, programming...
I understand that the NRF54LM20 reference suggests not to put any sort of resistor or capacitor components on the reset pin and simply rely on the internal pullup. Since this...
Hello,
We're trying to build a demo based on the BLE Audio sample with extra BLE services to transmit sensor data.
I have managed to build and run the BLE Audio sample...
Hello,
I am using the nRF52840 DK (same applies also for the dongle). The setup is quite simple. I have two nodes on my desk, one transmitting packets and the other receiving...
Dear NCS team,
I am developing an asynchronous UART driver using ncs v3.1.1. I observed that when calling uart_rx_enable() with a timeout value of 100 µs (at 115200 baud...
