Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I would have thought this was easy but I cannot seem to find a way to prevent LOG_INF etc from adding a line break to the log string.
I am using NRFConnect with Zephyr...
Hi,
I have TWIM communicating successfully with a slave device on the PCB.
We now need to support some PCBs populated with the slave device, and other PCBs where the slave...
I have a product running on an nrf5340 and part of it is running a nordic sample project. In the sample project there is a call to `k_msgq_get()`. The program spends a lot...
Hi
I'm evaluating the nrf5340dk devboard and are building a simple application on top of zephyr. I'm using Cmake and ninja on Ubuntu. The code builds and I'm able to flash...
Hi there,
We are currently doing some testing around the low power modes of the nrf5340. Detailed info on the Low Power mode and Constant Latency mode is a bit hard to find...
I'm trying to get my nrf9160dk board up and running with the nrfcloud service. However, when I input the SIM ICCID and PUK, the nrfcloud site starts it's "working" process...
Good day
After flashing a sample to my thingy 91 I seem to have lost the Jlink connection. All im picking up is the UART via nRF connect Programmer. Is there a Bin file...
Hello Sir/Mam;
I am new in nordic environment so i need your valuable guidance . i want to read a sensor data using Uart . I have successfully do same thing on Arduino board...
Hi,
I had previously asked about SPI interfacing of the RFID card reader and I was successful in creating a custom application using connect SDK 1.5.1.
But according to...
I currently have an application with B0->SPM->MCUBOOT->APP and am looking for an example of how to upgrade MCUBOOT itself over the air from a file downloaded from some server...
We're using a nRF52DK and the Nordic-Programmer-App to flash our firmware on our custom boards. After upgrading to Programmer v2.3.3 I'm getting the Error-Message "Part of...
Hi,
I am able to successfully build and flash applications from the CLI.
When setting up the nRF Connect VS Code extension, I run into an issue where it can't seem to...
Hello, I am trying to use the spi_flash sample project with a laird bl654 dvk. When I run the project however, dev->state->init_res = 19 and will not run for me. It recognizes...
Hi,
I have been trying for several days to modify the ble_app_uart project on the peripheral side to use the BLE Long Range, unsuccessfully. I use the NRF52833-DK with...
