Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi Nordic Team,
Currently we are exploring nRF52840 DK.
We have observed BLE Enable SOC usually have two cores, one as an application and one as BLE Soft Device core....
Hi - I am using the /nrf/samples/matter/lock sample as a reference template to develop my own app. Thank you for providing it!
I am able to build and flash the basic build...
After updating the firmware on NRF9160 Connect DK (using mfw_nrf9160_1.3.1.zip as well as the ltem asset tracker hex file) LED 3 does not turn on and AT commands in LTE Link...
I am using a mac M1, running macOS 12.0.1 Monterey.
J-Link Software and Documentation Pack v7.62 (latest)
NRF Connect for Desktop v3.10.0 (latest)
Programmer v2.3.1...
Hello,
i'm using a nrf52832 dk and i'm using the example ble app uart.
I saw the packets that are send for rx or tx but with packets of 20 bytes
I saw this post, https...
Hi,
I have some problem with NRF52840. When I use software example "ram_retention" in peripheral directory on 2 différents board I have 2 differents state of VBUS pin. ...
Hello,
I am relatively new to iOS development and have now made the iOS version of the nRF Toolbox from the Github. After some initial difficulties, I was able to get the...
Hi,
I have a peripheral device that running on nrf5340 and can be updated via MCUMGR SMP. i tested it via Device Manager application and it is working.
My question is...
I'm building a custom board based on nRF52840.
I'm providing 5V input via USB to VDDH & USB pins. The default output of the first internal regulator during high voltage...
Hi, before buying the PCA10056 kit, I have some questions about the USB CDC ACM example.
I'm new to the USB CDC ACM.
At the Infocenter , it says that
This example...
Hello everyone!
I have just got started working with Nordic devices, in particular the nRF9160. I have been doing tests using the provided UDP sample from nRF Connect SDK...
I tried building and running the buttonless DFU example project. However I get the following UART output:
It seems like it can download the softdevice by itself if the memory...
Hello, I recently picked up a nRF PPK2 and I'm liking it a lot.
I have it wired in-line with a battery (1500mAh li-po) with my device under under test. Measuring battery...
Hi,
I am using nRF52805 to transmit string data to the mobile end app "nRF Connect".
I found that sometimes the app will display hex data instead of the expected decimal...
