Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi, I have added libuarte example in-app template and sent data from Arduino to nRF52840 successfully. But after receiving some data and I am getting the following error....
Hi,
I use nrf5340 and have issue with i2c large buffer send: In order to flash page to bootloader with my application:
I defined
I defined static array with size...
Hello !
If I understand right and nrf_crypto is the main Crypto API in nRF SDK. They can be mapped to cc310 or to mbedtls sw routines.
Does exists nrf_crypto asynchronous...
Hi,
When I try to run a colleague's project on my PC in debug mode in Visual Studio Code, I get the error "Run to 'main' timed out. Trying to pause program":
The debug...
Hello, guys.
We have nRF51822 SoC with 256KB of Flash and 32KB of RAM memories at our disposal. For our application, we would need to use the BLE stack + over-the-air DFU...
Hello! I recently dived into using the nRF52840 SDK + Zephyr the goal is to use this for Bluetooth Long Range Extended Advertising. Are there available tutorials, resources...
Hello,
I am using sdk12,2.2 and nrf52832. I have interfaced bme680 sensor with nrf52. I am facing strange challenge.
My button interrupt is working every time but it stops...
Hi, I am working on nRF52811 as central and I want to put the device in full power save mode so it does not consume power and activate once I pressed the button. How can I...
Dear Sirs,
I am evaluating the option of controlling a couple of motors (each with an independent controller based on a nRF52840 device) from a Smartphone App. Both controllers...
Hi,
Im using an nRF5340 on the peripheral. Now i would like to use a Dongle on the PC-side, what device can you recommend?
nRF52840 Dongle ? Or is there an other dongle...
Hi, I'm using the serial_lte_modem sample application and I've modified the AT#XMQTTPUB command so that I can specify a slot number from which the device can grab a bank of...
I'm trying to use nrf_delay_ms function inside rtc_handler.
I was wondering if using delay function stops rtc from counting up, so it disrupts rtc interval time.
Hi all,
I´m trying to test the LWM2M Client sample.
After following all the steps explained in this web , when I run it and connect to the DevKit via Putty, I get the...
Hi!
We are debugging low power in our custom board which has several chips (nrff52840, nrf9160, acc, fuelgauge, pmic, etc etc).
We are seeing strange random increases...
Hi,
I have managed to upload the asset tracker via mcuboot to my Actinius Icarus.
It should straight-up connect to the actinius.io cloud, but when I check the link monitor...
