Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
Is there a low power consumption for battery powered long term (months) application for Nordic Thingy 91? I don´t need GPS position, just to receive sensor data and...
Hello
Using a Thingi91 with latest firmware and Asset Tracker v2. Connects to the tower, but cant seem to connect to the NRF Cloud. How can I check if it can reach any other...
Hello all
I am using the Thingi:91 in Sri Lanka. I can connect to the tower correctly, but cant get data connectivity yet. I am told by the operator that they use the following...
On nRF cloud I registered the ibasis sim card which came with the 9160DK and connected it to that 9160DK device. I'm now using a Fanstel BLG840F and wanted to know if the...
hello Nordic
i am using nrf52840, with zephyr
i wish to use the nrfConnect Tx power service to read and to SET my Tx power
but in ncs in zephyr/subsys/bluetooth/services...
Hi,
I am using nordic52840 dk board.
And i want to flash a bin file using nrfjprog command line.
For Hex file i am using below command
nrfjprog --reset --program blinky_pca10056...
Hi everyone,
We are using the nRF5340 and need to use an LFXO, not just for BLE, but also for the real-time clock that our product should provide.
Due to other requirements...
Dear Team,
Just I have purchased Thingy91. Please help with where I can see the demo to start with some basic example of transferring data. Mentioned that Pre-loaded assert...
I just installed the nRF toolchain and Programmer application to start using my nRF52840-DK eval board. I have the board connected through J2 to my computer and I can flash...
hello Nordic
i am using nrf52840 with zephyr ncs
unfortunatly i used this command "pamac install downgrade" at one point
since then i can not use 'west flash --erase...
nRF5 SDK > nRF5 SDK v15.0.0 > User Guides > Developing for nRF52810 gives a list of things to do to adapt an nRF528 32 project to an nRF528 10 target.
But, looking at...
Long story short.
I am trying to merge DFU master code to feed a DFU.zip to the DFU receiver code already present in the secure bootloaders (but elevated successfully into...
I'm working with firmware and hardware that has previously worked properly. I recently migrated to S113 from S140, and changed the data format of what was being set in the...
I am trying to create my first Freestanding Application under NRF Connect, I have SDK version 1.8.0. As soon as I click on "Create Application" I got the error message " Application...
