Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi Everyone,
Hope you all are doing well.
I'm using nrfConnect sdk v1.7.0 and vscode for development.
controller : nrf52833
Here I tried to build image with bluetooth...
Hi. I have been using this document to work on the Fanstel USB840F device. USB840F_User_Manual (squarespace.com) After erasing the device, I could'nt run this below command...
Hello, I am developing a custom board using the nRF52810 WLCSP package. I realized I made an error in the board layout after placing my order, the error being that I placed...
I made a DFU Bootloader for my nrf51822 that waits for two seconds before starting the application, so I have time to connect and flash.
That process was working with the...
If I set two separate UUID scan filters as below:
Is it possible to discern which event triggered the filter match?
At the moment on the scan_filter_match callback,...
Hello,
it's a nice concept to include sensors via the device tree and simply enable them in the project file. But I feel like I'm losing control of the sensor a bit. I don...
Hello nordic. I've been using the PPK2 to measure the current draw of the nRF9160DK. However, spi peripherals are not included in these measurements. I was told that if you...
Hi
I´am pretty new with the nRF connect sdk. I want to check the features from BLE long range /coded phy.
In the past I have allready worked with the ble_att_mtu_throughput...
hello Sirs
How can I put nrf5340-sdk in to extended mode to transfer 250 bytes of data over BLE radio?
the sample code I am using is Peripheral-uart example code.
Excuse me:
I want to implement nrf52833 run FreeRTOS，The nRF52840 project in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hrs_freertos\pca10056\s140\ses can only...
Hello All,
I am using NRF52833 in my project. I am also using RTOS in the code. I was previously working on NRF52840 but now I have migrated to NRF52833. I have changed...
I'm new to using NFC.
I've tried downloading a few NFC sample programs to my nRF5340-DK board and playing around a bit, but I ultimately want to implement something like...
We are using nordic SDK 16.0.0 and mesh SDK 4.2.0 with a nRF52840 chip.
Our products already have the provisioner/provisionee and config client/server implemented, based...
