When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
hi have the same problem related here: https://devzone.nordicsemi.com/f/nordic-q-a/91890/nrf52-reports-two-jlink-cdc-uart-ports
With revision 2, UART show only one...
We are looking into a device using the NRF54L to do low power indoor tracking since it has a very low power consumption when using the RADIO peripheral.
We see that the...
Hello,
I am facing an issue with nRF Cloud device provisioning. I am using the nrfcloud-util tool to provision the device to nRF Cloud (as recommended for production provisioning...
Hi all,
I’m running into issues flashing an Arduino Nano 33 BLE Rev2 (nRF52840) using Zephyr and the bossac runner. I consistently hit a “Flash erase failed” error and can...
Dear Nordic,
We’ve developed an application which runs on an nRF9151 DK using NCS 2.8.2. The device is running modem fw nrf91x1_2.0.2. Our application has enabled modem...
Hi I made a small production run of boards using nrf9151 where a handful of them have issues with nrf9151 such as not being able to flash. How do I debug the circuit at the...
Hi, I have a simple question. Is it possible, during the execution of Channel sounding ( ras_initiator ), for the initiator to regularly obtain the current RSSI from the reflector...
I am trying to flash an application image in nRF9160 on Thingy91. Thingy91 is in MCUBoot mode, and the selector switch is on nRF91 position. I get an error as below if I try...
Hello,
I am facing an issue building the NCS v3.1.0 Matter light bulb sample for nRF52840-DK:
cluster-enums-check.h:151:10: fatal error: clusters/TotalVolatileOrganicCompoundsConcentrationMeasurement...
Update: Its still working - I could resolve the issue with ChatGPTs expertise - the nrf Cloud evaluation key stored in Coiote was older then 30 days... Thats a thing which...
I'm trying to demonstrate that I can write a value to a Nordic npm1300 register and read the same value back. Using the code below, I write 0x5a but read 0x0a, so the msb...
Hi,
I am trying to get the PWM120 to work on nRF54H20 using SDK 3.1.0
As the starting point I am using the dimming PWM example which is working and I can get proper output...
