Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi there,
I'm intending to use the nrfxlib modem library and its BSD socket implementation on the nRF9160. My goal is to use non-blocking APIs and use `nrf_poll` in response...
Hi,
I followed the DFU to SDK example post on https://www.u-blox.com/en/docs/UBX-19050198 to add Buttonless DFU to an application (I modified \ble_peripheral\ble_app_hrs...
Hi,
I'm using nRF Connect SDK v1.7.0 to develop a firmware for a custom board with a nRF52832 MCU. I'm using VSCode to build and flash my device using the nRF Extension...
Hi All,
My dev environment is as follow:
nRF52832(Central) + S132 + SES + SDK 17.0.2
Normally my Multilink Central code is flashing and working properly without...
I'd like to know of an example(s) for interfacing nRF52840DK board as a Master SPI to an Arduino badge (from Honeywell). I have the badge working with an Arduino Uno (Rev...
Hi,
If I want to use the NRF52833 as TX, and NRF24LE1 as receiver. How I can I match out the address?
If NRf24le1,
RX_addr = {0x00, 0x 11, 0x 22, 0x 33, 0x 44}
then...
Hello,
I'm working with NCS 1.7.1 and the nrf52840 dev kit to implement a BLE peripheral with FOTA, stats and configuration features. I've added MCUMGR to the project so...
Hi Sir,
As we know the inductor connected to the DCCH pin is a DCDC function for high voltage mode.
But what side effect we can see if we connected the inductor at the...
Hi,
I'm using NRF52840 to connect to an Android mobile phone.
The application scans for advertisement and when the NRF device starts advertising - connection is established...
Hi,
I'm evaluating the performance of the Zigbee protocol implementation on the nRF connect SDK using nRF52840dk:s. nRF connect SDK 1.7.0, ZBOSS I'm not sure where to find...
Hi everyone,
We are using the secure bootloader in our board, and we are adapting that bootloader for our requirements. Moreover, we use the DFU updates for our Main application...
Hi,
I've noticed an issue with the modem locking up on the nRF9160DK. I'm not sure what causes it, but it always gets err 116 - ETIMEDOUT when initialising the modem and...
Hi,
I am trying to determine if PSA supports AES-256 encryption and decryption. From the documentation, it appears that it does. However, the aes-cbc example in the nRF...
