Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
I see a number of threads on the Nordic devzone where people are asking about official support for a DFU bootloader that combines BLE and UART for transports. Most...
hello Nordic
i am working with nrf52840, SDK16.0, s140 (maybe i will change softdevice later)
i build a project on the peripheral blinky example, i change the advertising...
Hello,
My application is based on the example "ble_thread_dyn_mtd_coap_cli" (nRF5_SDK_for_Thread_and_Zigbee_v4.1.0). I would like to be able to send large files via Bluetooth...
Setup -
nRF52840-DK
Nordic Connect SDK version 1.5.0
Sample - nrf/samples/peripheral/lpuart
Commented out "uart0" in the board specific overlay
Uncommented console...
Hello i'm trying to compilate the project secure_bootloader_ble_s132 but i'm having issue with micro-ecc.
when i complie on keil the bootloader exemple i get this error...
Hello,
As the question shows, how to add RTC function to a 5340 empty project?
condition
ncs:1.5.0
board: nrf5340dk
I have found a project,but it's 52840.
...
Hello,
My application runs in non-secure mode on the nRF9160, and I would like to disable external access to CPU, RAM and Flash.
I understand this is done by setting the...
Hello
I have board nRF52833 and i have several questions:
1. Is AoA example available ? I would prefer to have example of software for tag and for the localization...
On a custom board based on nrf52840.
We want to implement OTA DFU with radio (not necessarily BLE, e.g Serial 4G Modem)
We already checked the Serial DFU example and made...
Hi
I found the function
in nrf_ble_scan.c.
This decoding looks wrong to me since https://devzone.nordicsemi.com/f/nordic-q-a/27012/how-to-distinguish-between-random...
my gcc version: gcc-arm-none-eabi-9-2019-q4-major
defined in discarded section `.intList' of app/libapp.a(softuarte.cpp.obj)
////////////////////////////////////because...
Hi,
Is it at all possible to use the QSPI interface of nRF5340 to interface a micro SD card? Is sending custom instructions combined with long frames, as suggested here...
Hey Nordic team,
We have ECG/EGM alignment problem over BLE, the peer ble chip use RSL15, they came up with the below algorithm, which do need an API to get connection...
