Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi
I am using NC version 1.5.0 Dk version 0.15.0 .I am trying to get the AGPS data ..it's working sometimes and some times I'm facing the following error.Can you please...
Hi,
Is it possible to run a freeRTOS project on nRF52805?
I've follow the instructions from "Developing for the nRF52805 with nRF5 SDK" on the simple "blinky" example...
Hi,
I want to know a few things about sending large packets via BLE using nRF52 SDK 15.0 and above.
I am able to send the packets larger upto 128 Bytes. But i want to...
We are working on our development board contain the nRF52840. We also use Bluetooth Low Energy to load wirelessly the updated code with the DFU and it's working properly....
Dear Sir/Madam,
We are planning to devellop a remote control for resque equipement.
The remote controller and the host should pair 1 to 1. Pairing should be easy for the...
Hi.
I am going to make my own PCB with nrf52832.
Before making it, I have to check debugging through P20 in nrf52832 DK.
I have two nrf52832 DKs with SDK17.0.0.
I...
I am working on zigbee network where I wanted to get the tree of whole network but could not find any utility from nordic which can provide those info, so I have started developing...
Hi,
In my application, I'm trying to restart emulation because I want to switch from the NDEF static payload mode to ISO-DEP mode. The problem is that when I stop emulation...
Hello guys, looking forward to some help here!
I've been working on a Unit Test system setup with CMock + Unity for a BLE app. But when I try CMocking some headers in the...
Hi everyone,
I want to set TX_POWER using sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV,m_adv_handle,RADIO_TXPOWER_TXPOWER_Pos4dBm);
m_adv_handle = BLE_GAP_ADV_SET_HANDLE_NOT_SET;...
hi everyone ,
I have problem to set tx_power in my ble_ibaecon code.
I referred sdk15.0.0 ble_peripherals/ble_app_beacon example.
a ) First, I tried using below function...
I have downloaded the source code to use the following functions.
https://github.com/NordicPlayground/nRF52-ADC-examples
The following problem occurred in version 17,...
Hi Nordic Team,
I have a installed version of Segger Embedded Studio with both the normal version , and the "Nordic Edition".
When i build a sample project with nRF connect...
