Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
What is the reason for the two 1u/10V 0201 size capacitors in the reference design? I understand you possess much more sophisticated equipment and expertise than I do, but...
Hi,Team,
I'm using the nrf54l15-dk to develop zms to save custom configurations without affecting the pairing information of ble.
So I have a few questions: 1.Is the storage_partition...
Hi,
I'm developing an embedded GUI application using LVGL on the nRF5340 application core with Zephyr RTOS.
The display I'm using is an ST7789 TFT panel (240×284 resolution...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I am trying to set up an try a solution for channel sounding. I have a custom pcb that has the me54bs01 from minewsemi with the nrf54l15 and i am trying to test the example...
i have the nrf5833 dk board, i just started programming from quick start and it worked two times and now it does not program at all, programming failed
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
Is it possible to see LOG_INF() or LOG_ERR() messages from custom board software when the custom board is connected to a nRF52840DK through connector P20? The custom board...
Hi.
I am developing with NCS 2.7.0 using 5340 and have configured it to use 5 generic switches. These work fine. However, the order of the switches displayed in "Home" on...
Hello,
Used environment:
Board: nrf9151dk_nrf9151_ns
SDK Toolchain: v3.0.2
IDE: Vscode
I'm trying to test the LIS2DH sample using the nrf9151DK and the STEVAL...
Hi all
I have a project that I developed with SDK 17.0.2 in Segger Embedded Studio. It works well, but now I would like to add a GitHub Runner to compile it every time I...
