Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
just for your information:
the function nrfx_twim_xfer() prints always a warning, even if there was no transmission error. I guess NRFX_LOG_WARNING() should be logging...
I am trying to modify the https_client example from ncs\nrf\samples\nrf9160\https_client on Thingy91 so that it will retrieve an authentifcation token from AWS Cognito. So...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
The nRF52832 acts as SPI Slave and we want to wake up from Deepsleep when...
Hi
New to using EGU, trying to use it to implement software interrupts. How do I capture an Event?
I can see how to trigger and clear an event using -
nrf_egu_task_trigger...
In the function ble_init, I am getting an undefined reference to sd_softdevice_enable during the linking process. I see that in nrf_sdm.h there is SVCALL(SD_SOFTDEVICE_ENABLE...
Hello,
I am looking for the cost effective simultaneous central+peripheral solution using nrf BLE.
The nrf52810 seems to be hardware capable of doing this but I am...
Hi, I am creating custom ble service.there i need to perform
1. character - READ , NOTIF
2. character - WRITE READ
3 . character - READ,WRITE, NOTIF
I achieved ...
Hi
I'm on a custom board with NCS 1.2.0 and modem firmware 1.2.0.
We have implemented agps, and testing with 2 units with agps colocated with 1 unit without agps. All...
Strange device crash on deprovisioning.
This is probably something incredibly stupid, but I have been fighting this problem for a week and don't know where to turn.
I...
Hello
I program the example code peripheral " ble_app_hrs -pca10040e -s112" on nRF52810 and central " ble_app_hrs_c-pca10040 -s132" on nRF52832 .
I used nRF Toolbox on...
Hi,
we are working with Nrf52 and do not need/use Bluetooth, i.e. our devices will not have the Softdevice stack installed.
I was informed that for the radio certification...
Hello, I am using nRF52840, SDK 16, SoftDevice s140 with SES. I want to configure my device first in connectable mode and then in non-connectable beacon mode. sys_advertising_init...
