Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi engineers, I got a question regarding nRF52840 (PCA10056), i want to run DTM using PCA10056 board with MT8852B tester. Unfortunately, i keep failing to get the EUT address...
Dear all,
Our application is made of
Chip nRF518122 + SDK 11.0.0 + DFU Bootloader + BLE application (gcc complied) loaded with nRF Toolbox over the air
we are putting...
Hello,
the nRF9160 product specification 1.0 states in 5.1.4.2:
"Note: The LTE modem requires using LFXO as the LFCLK source."
I checked the clock register and noticed...
Hi,
I have developed an SWD working code which read-write the Flash Memory and RAM which is working very good.
Now I have a problem in I need to write start address...
Due to time pressure, I'm starting this thread based on an existing ticket: https://devzone.nordicsemi.com/f/nordic-q-a/51423/firmware-on-custom-board-application-bootloader...
Hi team,
We have a customer who has some questions about GPS.
The questions are:
Where do we save the Ephemeris data when GPS code start? RAM or flash?
When use...
Hi,
Can an nRF5x device be configured as a BLE relay with Bluetooth Mesh?
I believe with the Central-Peripheral-Relay example, the Relay needs to establish connection...
Hi. I am trying to create a dfu zip file that contains the softdevice, bootloader, and application. I am DFU upgrading an NRF52 device from SDK v13 to SDK v14 via Nordic's...
Hello,
we are using the nRF52840-DK.
File: secure_bootloader_ble_s140_pca10056.emProject
File: ble_app_buttonless_dfu_pca10056_s140.emProject
In short, we are...
Hi,
I have a well working cli environment under linux where i can compile, program and debug a nFR52 demo board.
I have installed RSSI Viewer (1.05) and Bluetooth Low...
We want to deactivate Mesh DFU packets relaying from the App side to avoid messing with the bootloader firmware. Is there any flag we may use for that?
Hi,
I'm trying to use a Bulk IN endpoint (EPIN3) and am running into an issue.
I call the nrf_drv_usbd_ep_is_busy() function to test whether it is safe to proceed with...
Hello
I am using buttons less DFU,
S132_nrf52_6.1.1 softtdevice
using Android + nrf connecct, I can update the device with DFU
using IPhone 6, I can not update...
I am able to provision using BlueZ's meshctl tool on Raspberry Pi3. However, after restarting meshctl, I am not able to control my device. I tried the "connect" command after...
