Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello.
I wrote a simple beacon application which advertises with uuid, major, minor and name. Now what I saw in sample beacon I found somewhere is that nrf connect properly...
Hello!I am using NRF52832. The antenna is aca-5036-a2-cc-s produced by INPAQ, but the bluetooth cannot be found.Whether the adaptive antenna can be provided and the technical...
Hi Every one,
I am trying to use two uart's communications concurrently in nrf51422, in my code i am running timer of one second.
Every one second in timer routine trying...
hi....
i am using nrf52382 and segger 15.2 version , i want my peripheral to send the data only if it reaches the certain limit (threshold value) on that case it should...
hello , friends
i am using nrf52832 ,debugged the ble uart program ,and then i tried to connect my device over ble uart app,i couldn't found my device ,then i tried to connect...
Good morning!
First of all, the background. I made a custom board and programmed it, everything worked like a charm. After that, I made another one, same hardware, same...
In my previous question , where I wanted to atomically send a large bulk of data, the solution was to keep track of p_bus-> free_buffers , in order to calculate the amount...
Hi,
I’m using SDK 15.00 and I have some issues with NFC. When I’m trying to connect with NFC - NFC_T2T_EVENT_FIELD_ON event occurs. At this point, I need to start BLE...
The release notes for S132 v6.1.1 lists a bug fix:
"Fixed an issue where NRF_TIMER0 may not be reset at the start of a radio timeslot (DRGN-10650)."
Did this bug exist...
Hi,
Here and here are examples of a port of the nice u8glib library to stm32. Based on these, i tried a port to nrf52, but was not successful so far.
I call the oled...
I am trying to save data to the flash memory. My starting file is the ble_app_uart_pca10040 (s132). I am using the sd_flash_write address is 0x007ffd0 and a value of 0; I...
We have developed a custom board using Raytac MDBT50Q with NRF52840. It has an external EEPROM and a RTC. We made an app that we use to program 4 daily alarms through BLE...
nRF51822-EK page is no longer available on the website. By any change I can get the PCA10001 schematic somewhere?
I would like to run some conductive RF testing and would...
