why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
I have flashed the light_ctrl hex file in nrf52840 dongle. Flashing Have been completed sueccessfully for provisioning in nrf mesh application its not showing in the network...
Hello,
For a Uni Project I want to measure the current of the Nordic Thingy:91 and visualize it. Therefore i bought the Power Profiler Kit 2. But i dont know how to connect...
So when changing the hci_icp.conf settings to have the configuration below, i get "CMake Error at C:/ncs/v2.6.1/zephyr/cmake/modules/kconfig.cmake:358 (message):" plus the...
My device is peripheral. I added a few lines before the advertisement start in main(). The whole project is in main and simply advertise and get connected and bonded.
...
I want to configure the ESB and nRF21540 chips on the NRF21540-DK. In order to compare the signal gain, I used the nRF52832-DK and burned the Bluetooth routine (without any...
Hello,
I have a project working on Nora B1, which I am testing on nrf5340DK. It is based on the Peripheral UART Sample, programmed with nfr Connect SDK v1.9.1. Now I need...
Hello,
This is probably a dumb question but, I'm having issues with an initial prototype for a product that has been given. The hardware engineer (me) designed and got...
Hi there,
Is switching between UART and I2C runtime on the nRF52840 with Zephyr possible when utilizing the same two pins for TX/RX vs SDA/SCL?
Thanks in advance,
L...
Quick Start can see the board - but says 'Not supported yet'
Load the programmer and select my board: The log looks like this:
19:07:18.801
Initialising nrfutil...
Hello,
In nRF Connect for Mobile, custom UUIDs show up as unknown, making it difficult to identify them easily.
Is there a way to add custom UUIDs, as can be done for...
Hi everyone,
I am testing modem shell application (2.6.1) for PPP support.
Here I am building the application using overlay-ppp.conf and ppp.overlay files.
after flashing...
Hello,
I am currently developing a product that is based on a nrf9160 and more precisely with a Thingy:91, this project integrates the tools of Golioth to communication...
Good morning!
I already looked at other questions in the forum but couldn't find any help. I'm trying to implement an example of Https with basic authentication on my nrf9160dk...
Dear sir:
The DAC private key is generated using P256, and the key length is 256 bits, which is 32 bytes.
As below link, why is 68 bytes planned in the factory data? ...
I'm following Intermediate course lesson 1 exercise 2 to use guiconfig.
When I try to open guiconfig,the output in terminal as follow:
How can I fix it?