Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I need to generate a clean 10kHz sine wave. I tried using PWM ( https://devzone.nordicsemi.com/f/nordic-q-a/89209/clarification-on-how-to-generate-a-10khz-sine-wave-with-pwm...
Hello, I followed this tutorial in order to setup custom BLE service. The tutorial as is works correctly and defines one service with an RX write characteristic and a TX notify...
Hi All,
I have implemented sleep mode in the firmware. I am using NRF52833 in my project. When the device is in idle state it goes in sleep mode. I am able to wakeup my...
I tried adding DFU support to my application by following this official tutorial:
But, I get the following errors:
/opt/nordic/ncs/toolchains/v2.0.0/opt/zephyr-sdk...
We're using sd_flash_write() and sd_flash_page_erase() to store some data to internal NOR FLASH at runtime. We have these calls integrated with the RTOS we're using in a HAL...
I've been using nRF Connect for Desktop a lot recently for power measurements with the PPK2 and to program nRF52840Dongles. I keep stumbling over a small missing feature:...
Hello,
I saw in the documentation for the softdevice s132 v5.10 (which is for production use now), I saw it supports changeable MTU. I have searched for the maximum supported...
Hi all
I have a problem with allocate RAM.
I build the project as non secure.
in the zephyr.dts file, you can see that the memory is divided into 3 areas:
sram0_s...
Hi
I have nrf52833DK it was working all fine but suddenly the LED5 is not lighting up and it is not detected by USB port. I tried to check the board voltage regulators and...
Hello,
I just started working on the nRF52 series controller, I want to upgrade my project using BLE features.
I need 1 master device to send to multiple slave devices...
Hi,
According to CryptoCell-312 documentation , it supports the SHA-1 algorithm. I was able to successfully run the SHA-256 cryptography sample application in the nRF Connect...
In my application, I need to use the nrf52840 for both BLE (as the controller) and ShockBurst. Specifically, it's the nrf52840 on the nrf9160 if it matters. I'm using the...
Hi Team,
We are working on nRF52840 SOC with BLE functionalities.
We need the mechanism for to find out the BLE or BLE Stack is in Hanging state before the processor is...
Hi,
I'm trying to build a proof of concept for a BLE gateway that captures data from BLE sensors and sends it to the cloud via LTE-M connection. I'm hoping that the gateway...
problem description:
hi, I just got a PCA10040 development board with which I plan to learn about nrf connect SDK.
so I try the common BLE peripheral demo,but I 've met...
